Registering Peripherals; Modifying General Parameters; Setting The Date And Time - Honeywell Domonial CMI800 Manual Del Usario

EKZ008500A

2-2 Registering peripherals

Screen Action
Select option 1 1 1 1 - - - - REGISTER
Programming main menu
Registering Perform the action indicated into the peripheral notice to
register it ; generally a tamper opening.
Type OK
View device
Select option 1 1 1 1 - - - - LABEL
Edit device
Label Delete the original label, and replace it with the
localization of the peripheral, e.g. ENTRANCE, then
validate with OK
Select option 2 2 2 2 - - - - EDIT
Modify device
Select address Type in the address code, such as 1323 to select a zone for
a detector, then OK
Annex 2 of this document.
Set value Type in the allocated zone for the detector :
0 for Total, 1 for Part, 2 for Annex or 3 for 24/24, then
validate with OK
Select address Proceed identically with other parameters for the same
detector, according to the codes reference annex. When
finished, return to main menu with
If the TCU used for programming must be left on the installation, it can be registered by pressing simultaneously the Total arm and Part arm
keys while the panel is waiting for a registering message.
VIEW DEVICE VIEW DEVICE VIEW DEVICE VIEW DEVICE MODIFY DE MODIFY MODIFY MODIFY
LBL 1-LABEL
Intervenant
TYPE DO CH D1 2-EDIT
3-DELETE
FAULTS - T -
EDIT (OK) EDIT (OK)
EDIT (OK) EDIT (OK)
2-3 Modifying or deleting registered devices
Screen Action
Select option 2 2 2 2 - - - - VIEW
Programming main menu
View device Use the arrows keys to select among the registered or
predefined devices, then validate with OK
Edit device Proceed with device edition as described in the registering
procedure above.
Alternatively, select option 3 3 3 3 - - - - DELETE
Edit device
Validate with OK
Confirmation

2-4 Modifying general parameters

Screen Action
Select option 3 3 3 3 - - - - PARAMETERS
Programming main menu
Select address Proceed as for devices parameters, using the general
parameters section of the address codes annex. For
example, code 331126 will address the entry delay.

2-5 Setting the date and time

Screen Action
Select option 4 4 4 4 - - - - DATE & TIME
Programming main menu
Key in the required value, then validate with OK
Set date & time
REGISTER
REGISTER REGISTER
OK to enter device edition mode
OK OK
LABEL LABEL LABEL
OK.
OK OK
EDIT EDIT EDIT
OK. Usual address codes can be found in
OK OK
OK
OK OK
DE DEVICE DE VICE VICE VICE LABEL LABEL LABEL LABEL
LABEL
-----------------
CANCEL CANCEL ( ) VAL CANCEL CANCEL
VIEW DEVICES VIEW VIEW DEVICES DEVICES DEVICES
DELETE
DELETE DELETE
OK OK OK
PARAMETERS PARAMETERS PARAMETERS
DATE & TIME DATE & TIME DATE & TIME
Result
The panel waits for a registering message from any
peripheral.
Once the message has been received by the panel,
the TCU will present the View device screen. The
initial device label is its serial number.
> Edit device menu
> Set label screen
> View device screen
> Select address screen
>Set value screen
>Select address screen
> Programming main menu
SELECT ADDRESS SELECT ADDRESS SELECT ADDRESS SELECT ADDRESS
LBL
Intervenant
TYPE F4
ADDRESS
_
1323
VAL(OK) VAL VAL (OK) (OK) (OK) CANCEL CANCEL CANCEL CANCEL( ) VAL(OK)
Result
> View device screen
> Edit device screen
OK.
OK OK
> Confirmation screen
The device is deleted.
> View device
Result
> Select address screen
Result
> Set date & time screen
OK
OK OK > Programming main menu
VALUE VALUE VALUE VALUE
LBL
Intervenant
TYPE F4
1323
DATA:
_
0
VAL(OK) VAL(OK) VAL(OK) NO NO( ) NO NO YES(OK) YES YES YES
E
N
5/64
G
L
I
S
H
(OK) (OK) (OK)