Declaration Of Conformity; Specified Use; General Safety Instructions; Special Safety Instructions - Metabo KHE 56 Manual Original

Original instructions

1. Declaration of Conformity

On our own responsibility, we hereby declare that
this drilling and chisel hammer, identified by type
and serial number *1), meets all relevant
requirements of directives *2) and standards *3).
Technical documents for *4) - see Page 3..
MHE 56: 2000/14/EC: Procedure for assessing
conformity as per Appendix VI. (Testing centre:
VDE Testing and Certification Institute, Merianstr.
28, 63069 Offenbach, Germany).

2. Specified Use

The KHE 56 is designed for hammer drilling and
chiselling in concrete, bricks, stone and similar
materials when used in combination with
appropriate accessories.
The MHE 56 is designed for chiselling in concrete,
bricks, stone and similar materials when used in
combination with appropriate accessories.
The user bears sole responsibility for damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Before using this power tool, carefully read
through and familiarise yourself with all the
enclosed safety information (red booklet)
and the instructions. Keep all enclosed
documentation for future reference, and pass on
your power tool only together with this
documentation.

4. Special Safety Instructions

For your own protection and for the
protection of your power tool pay
attention to all parts of the text that are
marked with this symbol!
Wear ear protectors. Exposure to noise can
cause loss of hearing.
Use the additional handles supplied with the
tool. Loss of control can lead to injuries.
Hold the power tool by insulated gripping
surfaces when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and shock the operator.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Always work with the additional handle correctly
installed.
Always hold the machine with both hands using the
handles provided, stand securely and concentrate.
Always wear protective goggles, gloves, a dust
mask and sturdy shoes when working with this tool.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Always work with the tool attached correctly. Pull on
the tool to check that it is seated correctly. (It must
be possible to move the tool a few centimetres in an
axial direction.)
When working above ground level, make sure that
the area underneath is free.
Do not touch the tool or parts close to the tool
immediately after stopping work because they may
still be extremely hot and could cause skin burns.
Always lay the power cable away from the back of
the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Reduce dust exposure:
Some of the dust created using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some
examples of these chemicals are: Lead from lead-
based paints, crystalline silica from bricks and
cement and other masonry products, arsenic and
chromium from chemically-treated lumber, hard
wood like oak or beech, metals, asbestos.
The risk from exposure to such substance will
depends on how long you or bystanders are being
exposed.
Do not let particles enter the body.
To reduce your exposure to these substances: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
ENGLISH en
13