Tabla de contenido
Idiomas disponibles
Idiomas disponibles
You can select the sound input level of the Bluetooth device.
Press [PLAY MODE] repeatedly to select
"LEVEL
0". "LEVEL +1"
or "LEVEL
+2".
•
Select "LEVEL 0" if the sound is distorted.
Press [DISPLAY,
-DIMMER]
repeatedly to view the information
of
the current connected
device.
[-_ BLUETOOTH
device
Connected
--
Connecteo profiles _
name
This unit works as a Bluetooth
hands-free
for your mobile pnones.
You can answer or cancel an incoming call with the remote control
Press [ "% ] "CALLING"
starts blinking on the
display (Talk into the unit's mlcroDnone!.
Press [ '% ] agam to transfer the call to the
mobile Dnones
"TRANSFER"
blinks. You may
now converse
using the mobile phone).
T_ cahc_l fi call
Press [M,_',_].
Press [+, VOL ._, -] (Adjustable from
"TEL VOL 1" to "TEL VOL 10").
Press [MUTE].
Press again to cancel.
(During "MIC MUTE", the caller is not able to
hear your voice).
•
This unit does not work with Headset
Profile (HSP).
•
When the mobile phone is too close to the microphone
of this unit,
noise may occur. Always keep the mobile phone away from the
microphone
of this unit when making a call.
0) Press [OMENU]
to display
"DISCONNECT?"
and then press
[OK].
A confirmation
message is displayed.
_2_Press [A,V]
to select
"YES" or "NO"
and then press [OK].
•
The connection
can also be stopped when you disable Bluetooth
transmission
on the connected
Bluetooth device.
m To register more devices
_1)Press [0MENU].
(2_Press [_.,V] to select "NEW DEV" and then press [OK].
The unit enters pairing mode and "PAIRING"
starts blinking on the
display.
_3_ W hile this unit is in pairing mode, access
the Bluetoeth
menu of
the Bluetooth device and execute a Blueteeth
search
to find this
unit (SC=HC40).
.
If prompted for the passkey, enter "0000".
m To select communication
quality
_1)Press [OMENU].
(2_Press [,_,Y] to select "LINK
MODE" and then press [OK].
_3_ Press [A,V] to select the following
modes
and then press [OK].
.
"MODE 1": Connection
with emphasis
on communication
stability
.
"MODE 2": Connection
with high bit rate for good audio quality
(Communication
might easily be disconnected
in this
mode, select "MODE 1" if this occurs).
m To select Auto Link mode
0) Press [OMENU].
_ Press [A,Y]
to select "AUTO
LINK" and then press [OK].
_3_ Press [A,V]
to select the following
modes
and then press [OK].
.
"ON": Automatically
linked even in other than Bluetooth
selector
.
"OFF": Linked only in Bluetooth selector
•
These functions are unavailable
if a device is connected.
Disconnect
the Bluetooth devices to display these functions.
•
When "LINKING"
is displayed, pressing
[QMENU]
is invalid.
•
Auto Link works only if your device support A2DP.
The remote control and main unit are factory-set to "REMOTE
1" mode.
If you find the remote control unintentionally
also controls other
equipment,
you can switch to operate in "REMOTE
2" mode.
To switch
to "REMOTE 2" mode (by main unit only)
_.1) P ress [FM/AM/AUX]
to select "AUX".
_2_Press and hem [FM/AM/AUX]
and then press [2] until
"REMOTE
2" is displayed.
_3_ Press and hold [OK] and [2] for at least 2 seconds.
To return to "REMOTE
1 " mode
Repeat the steps above but replace [2] with [1].
("REMOTE
1" will be displayed.)
When the following situations
occur, reset the memory:
•
There is no response when buttons are pressed.
•
You want to clear and reset the memory contents.
To reset memory
_,1) D isconnect
the AC power supply
cord. (Wait for at least 3 minutes before proceeding
to step 2.)
(2) While pressing and holding down [_)/I, POWER]
on the main unit, reconnect
the AC power supply
cord.
"appears
on the display.
_;) Release [o/I, POWER].
All the settings are returned to the factory preset. You will need to reset the memory items.
O
CC
14
Tabla de contenido
