Nice Neomat T Serie Manual De Instrucciones página 8

4.3.4) Programming of the "wind" weather sensor level
If a "VOLO", "VOLO S" or "VOLO ST" wind sensor is connected to the "sensors" input, the wind protection is activated that automatically
retracts the awning when the wind exceeds the programmed level. If the level is exceeded for more than 3 seconds, a command that is the
same as the ▲ button is activated and any other movement is blocked until the wind level returns below the programmed level for more than
1 minute. There is a choice of 5 different activation levels: 1=5Km/h, 2=10Km/h, 3=15Km/h, 4=30Km/h and 5=45Km/h. (the level is factory
set at No.3).
The wind and sun activation thresholds of the "VOLO ST" sensor are programmed directly on the sensor (see "VOLO ST" instructions).
To modified the programmed level:
Table "A9" Changing the activation level of the "wind" protection
Press and hold down button ■ of a previously memorized transmitter until you hear a
1.
beep (after about 5 seconds) then release it.
Slowly press button ▲ the same number of times (1, 2, 3, 4 or 5) as the desired level
2.
3. After a few moments you will hear a number of beeps equal to the required level
Press and release button ■ to confirm
4.
If at point 3 you don't here the number of beeps equal to the desired level, simply do not press anymore buttons and wait a few seconds for
it to finish without changing the level.
4.3.5) Programming of the "sun" weather sensor level
If a "VOLO S" sun sensor is connected to the "sensors" input, the sun automation is activated that automatically lowers the awning when the
"sun" exceeds the programmed level. If the level is exceeded for more than 2 minutes, a command that is the same as the ▼ button is acti-
vated and if the sun drops below the programmed level for 15 minutes, a command is activated that is the same as button ▲. The automa-
tion can be deactivated by sending a "Sun OFF" command with the transmitter, and subsequently reactivated with a "Sun ON" command. A
▲ or ▼ command can in any case be sent when the "sun" automation is on that override the automation commands. The "wind" protection
overrides the "sun" automation at all times.
There is a choice of 5 different "sun" activation levels: 1=5Klux, 2=10Klux, 3=15Klux, 4=30Klux and 5=45Klux (the level is factory set at No. 3).
Table "A10" Changing the activation level of the "sun" automation
Press and hold down button ■ of a previously memorized transmitter until you hear a
1.
beep (after about 5 seconds) then release it.
Slowly press button ▼ the same number of times (1, 2, 3, 4 or 5) as the desired level
2.
3. After a few moments you will hear a number of beeps equal to the required level
Press and release button ■ to confirm
4.
If at point 3 you don't here the number of beeps equal to the desired level, simply do not press anymore buttons and wait a few seconds for
it to finish without changing the level.
8
Example
5s
X1 = 5 Km/h
X2 = 10 Km/h
X3 = 15 Km/h
X4 = 30 Km/h
X5 = 45 Km/h
X1 = 5 Km/h
X2 = 10 Km/h
X3 = 15 Km/h
X4 = 30 Km/h
X5 = 45 Km/h
Example
5s
X1 = 5 Klux
X2 = 10 Klux
X3 = 15 Klux
X4 = 30 Klux
X5 = 45 Klux
X1 = 5 Klux
X2 = 10 Klux
X3 = 15 Klux
X4 = 30 Klux
X5 = 45 Klux