Mounting The Hood; Install Range Hood Internal Blower Motor - Samsung NK36R9600CS/AA Guía De Instrucciones Para Instalación

Installation
3. Drill a 1 ⁄ " (3.2 cm) hole at this location.
1
4
4. Pull enough power supply cable through the wall to allow for easy
connection to the terminal box.
5. Remove the terminal box cover and set aside.
6. Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent transition
with damper to the top of the range hood (depending on your
installation), using 4- 3.5 x 9.5 (.15 x.37 in) mm screws.
7. Remove the knockout from the back of the range hood and install a
UL listed or CSA approved ⁄
1
A
NOTE: The exhaust adaptor/damper can be installed up to 1 inch
on either side of the hood center to accomodate off-center ductwork.
In extreme off-center installations, one end of the duct connector may
need to be trimmed to clear the electrical cable clamp.
8. Place the range hood near its mounting position and run the power
supply cable through the strain relief into the terminal box (enough to
make connection).
9. Tighten the strain relief screws.
10. Make the electrical connection. See the "Electrical connection"
section.

Mounting the hood

NOTE: Mark the Range Hood knockouts on the wall, and then make
the necessary cutouts before the installation.
NOTE: The range hood attaches to the wall by the 6 mounting screws in
the wood support mounted to the wall.
To mount the hood, follow these steps:
1. Using 2 or more people, hang the range hood on the wall by placing
the 2 screws mounted in the wood support attached to the wall
through the wide portion of the slotted holes in the back of the range
hood.
NOTE: If your installation uses the optional duct cover, the vent
system needs to be connected to the range hood and the duct cover
mounted to the top of the range hood before you tighten the mounting
screws.
2. Pull the range hood down so the screws protrude through the narrow
portions of the slots, align the bottom of the hood with the horizontal
line marking the hood bottom, level the hood, and then tighten the 2
mounting screws.
3. Mark 2 lower mounting hole locations. Drill
if the holes will be drilled into wood studs or framing. If the holes will
not be drilled into wood, drill two
10 x 50 mm (.4 x 2 in) wall anchors. Install 2 - 6 x 80 mm (.25 x 3.15
in) screws with 5.3 x 20 mm (.21 x .8 in) washers (D and C) into the
lower mounting holes, and then tighten.
" (1.3 cm) strain relief.
2
A
B
A. 4 - 3.5x9.5 mm screws
B. Knockout
⁄ " (0.32 cm) pilot holes
1
8
⁄ " (0.95 cm) pilot holes and insert
3
8
B
C
B
D
4. Install the 4 - 4.2 x 19 mm (.17 x .75 in) screws (B) through the back
of the hood into the wood support, and then tighten.
5. Connect the vent system to the hood. Seal all joint with clamps.

Install Range Hood Internal Blower Motor

1. Place the range hood blower motor assembly inside the range hood
Blower motor assembly
A. Wiring connection
2. Slide the left mounting plate flange under the motor mounting
bracket.
A
B
A. Motor mounting bracket
B. Mounting plate left flange
A
A. Mounting screws
B. 4 screws - 4.2 x19 mm
C. 2 D5.3 x 20 mm washers
D. 2 screws - 6 x 80 mm
A
English 9