Campbell Hausfeld MF349099 Instrucciones De Operación, Instalación Y Mantenimiento página 4

Operating Instructions and Parts Manual
Important Safety Information (Continued)
e. Use tool within safe and proper temperature range. The
operating environment for this tool is between 32°F (0°C)
and 104°F (40°C). The tool may fail to operate correctly at
temperatures above or below the temperature range.
Do not drive a fastener on top of other
fasteners. The fastener could glance off
and cause death or a serious puncture wound.
Do not expose tool to extreme heat.
f. Keep all screws, bolts, and covers tightly secured.
Check tool periodically for any loose screws or bolts. Make
sure all covers do not slide out of place.
g. Do not drive fasteners into thin boards or near corners /
edges of work piece. Fasteners can unintentionally be
driven completely through and cause damage. Check depth
adjust before using tool.
h. Do not disassemble tool.
Do not make any modifi cations to the tool
without fi rst obtaining written approval
from Campbell Hausfeld. Do not modify or alter the nailer or
any nailer parts. Do not use the nailer if any shields or guards
are removed or altered. Do not use the nailer as a hammer.
Personal injury or tool damage may occur.
Never use gasoline or other
fl ammable liquids to clean
the nailer. Never use the nailer in the presence of
fl ammable liquids or gases. Vapors could ignite by
a spark and cause an explosion which will result in
death or serious personal injury.
BATTERY / FUEL CELL SAFETY
The fuel cell of
this tool is an
aerosol dispenser that is fl ammable
and combustible. Failure to follow
instructions on tool use and/or safety
warnings may result in explosion or fi re. Keep the nailer, fuel
cell(s), and battery away from continuous direct sunlight and
temperatures exceeding 120°F (49°C), otherwise the fuel cell
and/or battery may burst.
No smoking while
using this tool. The
aerosol fuel cell and tool exhaust is
fl ammable and will ignite if exposed to
fl ame or burning substances. Smoking
during use or shortly after use of this tool will create a
potential safety hazard.
Do not incinerate or refi ll the fuel cell or
battery of this tool. Do not burn the fuel
cell, even after fuel cell is completely depleted. Follow proper
disposal instructions and local regulations for the fuel cell and
battery.
NOTE: Battery temperature will increase during and shortly
after use.
4 www.chpower.com
Battery shelf life - The included battery may be in a slightly
depleted state or dead depending on how long the product has
awaited purchase. Charge battery. If it does not charge, please
call Campbell Hausfeld at 1-800-543-6400 for assistance. DO
NOT RETURN TO THE STORE.
Take the fuel cell and battery out of the tool for the
following:
◆
Doing any maintenance or inspections
◆
Clearing a jam
◆
The tool is not in use
◆
The user is leaving the work area
◆
Moving or transporting tool to another location/work site
◆
Leaving the tool unattended
STORAGE / END OF USE
When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws, other small metal objects that
can make a connection from one terminal to another. Shorting
the battery terminals together may cause sparks, burns, or
fi re.
a. Remove battery when storing tool for an extended time.
b. Do not store in locations where the temperature may
reach or exceed 120°F (49°C), such as a metal tool shed,
or a car in the summer. This can lead to deterioration of
the battery.
c. When not in use, the tool, fuel cell, and battery should
be stored in a cool, dry place. Remove battery and fuel
cell and store in case.
SERVICE
a. Tool service must be performed only by qualified repair
personnel.
b. When servicing a tool, use only identical replacement
parts. Use only authorized parts.
Disconnect fuel cell and battery and
release tension from the pusher before
attempting to clear jams. Personal injury and/or tool damage
may occur.
The DANGER, WARNING, CAUTION, and NOTICE
notifications and instructions in this manual cannot
cover all possible conditions and situations that may
occur. It must be understood by the operator that
common sense and caution are factors which cannot
be built into this product, but must be supplied by the
operator.
NF349099