Campbell Hausfeld MF349099 Instrucciones De Operación, Instalación Y Mantenimiento página 13

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Operating Instructions and Parts Manual
Troubleshooting Guide
Stop using nailer immediately if any of the following problems occur. Serious personal injury could result.
Any repairs or replacements must be done by a Qualifi ed Service Person or Authorized Service Center.
General Problems (Continued)
SYMPTOM
Driver blade of tool does not
operate smoothly or return to
pre-fire position.
Tool operates properly, but
fastener does not drive
completely into work surface.
Tool operates erratically.
Tool LED is green.
Tool does not fire fastener
every time trigger is pulled.
Tool does not drive fastener.
Fan comes on, fuel cell is
confirmed to have fuel, and
WCE moves freely.
CAUSE
1.
Driver blade is dirty or debris is in
pathway
2.
Driver blade is bent
3.
Exhaust valve dirty or deformed due to
excessive usage and heat
4.
Filter is blocked or dirty; tool is
overheating
5.
Screws loose
1.
Fastener depth adjust not set correctly 1.
2.
Fuel cell is low
3.
Leak in fuel system
1.
Fuel cell is low
2.
Malfunction in electrical components
3.
Filter is blocked or dirty; tool is
overheating
4.
Tool is dirty
5.
Filter is blocked or dirty; tool is
overheating
6.
Screws loose
1.
Check fasteners
2.
Fastener pusher malfunction
3.
Magazine spring weak or damaged
4.
Driver blade worn or damaged
5.
Check driver blade of tool has returned
to pre-fire position
6.
Driver blade is dirty or debris is in
pathway
7.
Filter is blocked or dirty; tool is
overheating
8.
Screws loose
1.
Dirty or worn spark plug
2.
Check wiring for breaks or
disconnected plugs
SOLUTION
1.
Remove battery and fuel cell, then clean driver
blade pathway or remove debris.
2.
Do not use tool.
Call 1-800-543-6400 for assistance.
3.
Remove battery, fasteners, and fuel cell. Clean if
dirty and replace if deformed.
4.
Remove and clean filter.
5.
Check connections and tighten if necessary.
Follow instruction in Operation section for
Adjusting Fastener Depth.
2.
Check fuel cell, metering valve connection, and/or
replace with new fuel cell if necessary.
3.
Depress WCE against the work surface and hold in
place for a few seconds. Pull the trigger to actuate
tool. Fastener should drive into work surface. If no
fastener is driven, there may be a leak in the fuel
delivery system.
Discontinue use and call 1-800-543-6400 for
assistance.
1.
Check fuel cell. Replace fuel cell if necessary.
2.
Call 1-800-543-6400 for assistance.
3.
Remove filter element and clean; inspect exhaust
and remove any debris or blockage. Allow tool to
cool down if exhaust port is warmer to the touch
than when in normal use.
4.
Clean tool.
5.
Remove and clean filter.
6.
Check connections and tighten if necessary.
1.
Remove fasteners and check compatibility.
Only use compatible fasteners.
2.
Unload fasteners, check fastener pusher operation,
and/or clean magazine.
3.
Replace spring in magazine.
Call 1-800-543-6400 for assistance.
4.
Call 1-800-543-6400 for assistance and
replacement part.
5.
If driver blade is not in pre-fire position, the trigger
was not pulled all the way. Depress WCE against
scrap piece work surface and pull trigger. This
should return driver blade to pre-fire position. If it
does not, remove fasteners, battery, and fuel cell.
Call 1-800-543-6400 for assistance.
6.
Remove battery and fuel cell, then clean driver
blade pathway or remove debris.
7.
Remove and clean filter.
8.
Check connections and tighten if necessary.
1.
Remove and clean spark plug. Reinsert spark plug
and attempt to operate. If still not working, replace
spark plug.
2.
Replace plug and / or wiring harness and / or
e-module (in that order).
NF349099
www.chpower.com
13
Tabla de contenido
loading

Tabla de contenido