Declared Use - Zhermack Hurrimix 2 C305140 Manual Del Usuario

Recommended separation distances between portable and mobile radiocommunications equipment and hurrimix
Hurrimix is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The client or Hurrimix
2
electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and Hurrimix
according to the maximum output power of the communications equipment, as recommended below.
EN
Rated maximum output power of
the transmitter
W
0,01
0,1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the
equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer.
Note 1: At 80 MHz and 800MHz, the separation distance for the highest frequency range applies.
Nota 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and
people.
6.7 ZhERMACK PRESET PROGRAMS
Hurrimix software has 20 mixing programs, divided as follows:
2
• Alginate section: 10 programs, 7 of which are preset (specific for Zhermack
products) and 3 can be managed by the user.
• Plaster section: 10 programs, 7 of which are preset (specific for Zhermack
products) and 3 can be managed by the user.
All programs can be modified by the user: By pressing buttons
"+" and "-", the mixing time can be increased or decreased (from
a minimum of 2 to a maximum of 30 seconds).
Alginates
Hydrocolor 5
Hydrogum 5
Hydrogum
Orthoprint
Tropicalgin
Phase Plus
Neocolloid
Prog. 1
Prog. 2
Prog. 3
Dental Stones
Elite Rock
Elite Master
Elite Model
Elite Model Fast
Elite Stone
Elite Ortho
Elite Arti
Prog. 1
Prog. 2
Prog. 3
To reset the default programs, press and hold button 8b (fig. A)
and at the same time, turn the device on by pressing button 7
(fig. A).
6.8

DECLARED USE

Hurrimix mixer has been designed to mix alginates and plasters for the
2
dental industry.
6.9 NON-DECLARED/PROhIBITED USE
Using the equipment for any purpose not considered in
paragraph regarding "Declared use" shall be considered
improper and thus forbidden.
The improper use of the equipment renders the warranty null
and void and Zhermack declines all liability for any damage to
objects and injury to operators or third parties.
The main reasons for which the warranty is rendered null and void are given
in paragraph 2.2 and in the "Warranty Certificate" attached to this Manual.
The reference figures are present on pages 3, 4, 5 and 6 of this manual and in the product Quick Guide.
26
Separation distance according to the frequency of the transmitter
150 kHz to 80 MHz
d = [3,5/V ] √P
1
0,12
0,38
1,2
3,8
12
Time Mixing
6 sec
6 sec
10 sec
6 sec
8 sec
8 sec
10 sec
6 sec
8 sec
10 sec
Time Mixing
6 sec
6 sec
8 sec
6 sec
6 sec
6 sec
8 sec
6 sec
8 sec
10 sec
m
80 MHz to 800 MHz
d = [3,5/E ] √P
1
0,12
0,38
1,2
3,8
12
ChAPTER 7: USING ThE EqUIPMENT
7.1 GENERAL WARNINGS
For total certainty of safe operation, scrupulously follow the
work phases given below.
For greater clarity, the numbers stated in the figures positioned
near to the paragraph boxes correspond to the numbering of
the data in Chapter 3, regarding the "Description of the
equipment".
To avoid the occurrence of any risks, pay attention to avoid
pouring water during the preparation on the electrical voltage
parts.
To avoid any interference, the equipment has been projected to
perform a mixing cycle every 3 minutes.
7.2 USE OF ThE MIXER WITh ALGINATE
Do not activate the device without material inside the container.
Hurrimix 2 mixes the most common alginates; recommended
quantity 60g, max 80g (powder + water). Do not exceed the
maximum permitted quantity to avoid malfunction.
The device guarantees the best results by using Zhermack
alginates.
Once it has been correctly installed and put into service, proceed as follows:
Fig. 5: Press the program button (fig. A, 8a - 8b) to scroll and select the
desired program in the Alginates section (fig.5, A).
Mixing time can be customised, by pressing buttons "+" (fig.A, 9) and "-"
(fig.A,10). Keep the button pressed for a fast scroll.
Fig. 6: before opening the lid, opening must be enabled by briefly pressing
the release button (fig. A, 7). The lid can be opened 3 seconds after pressing
the button.
Fig. 7: Dose the alginate powder with a measuring cup as suggested by the
Manufacturer and pour it in the appropriate container of alginate mixing.
Comply with the dosage indicated by the Manufacturer.
Fig. 8: Add the correct quantity of water, using the bottle with graduated
measuring cup (provided with).
Keep away from Hurrimix 2 when you pour water into the bowl
to prevent water from spilling over it.
2
user can help prevent
2
,
2
800 MHz to 2,5 GHz
d = [7/E ] √P
1
0,23
0,73
2,3
7,3
23
hurrimix 2