Tabla de contenido
Idiomas disponibles
Idiomas disponibles
6. Technical Data
Nominal input voltage
Power consumption
Measurement idling speed n
Safety class
Protection category
Weight
Grinding angle range
Sharpness drill diameter
Sharpness knife width
Grinding disc:
Outer diameter
Borehole diameter
* Operating mode S3 - 15% - 10min: S3 = Intermit-
tent mode without influencing the starting pro-
cess. This means that during a period of 10 min
the max. operating time is 15% (1.5 min).
Noise values
The total noise values determined in accordance
with EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
7. Assembly
m Caution! Risk of injury!
• Ensure that you have sufficient space in which to
work, and that you do not endanger other people.
• All covers and protective devices must be assem-
bled properly before commissioning.
• Disconnect the mains plug before changing the
setting on the device.
Setting up
Place the sharpening station on firm surface and fas-
ten the device. Ideally, bolt the drill to the surface.
Use the mounting holes for the work bench assembly
(9) in the baseplate for this.
The screws and nuts required for assembly are not
part of the scope of delivery.
20 | GB
www.scheppach.com / [email protected] / +(49)-08223-4002-99 / +(49)-08223-4002-58
230V~ 50Hz
65W (S3 15%)*
6700 min
-1
0
II
IP20
1.5 kg
20° - 40°
3 - 10mm
6 - 51mm
max. 48mm
10mm
74 dB(A)
3 dB
87 dB(A)
3 dB
Mount the sharpener
1. Select one of the three sharpeners.
2. In order to remove a sharpener from the working
position, you must press down the release lever
for the sharpener (13).
3. Remove the sharpener from the guide rails, up-
wards.
4. In the storage positions, the sharpeners are not
fixed to the right and left side and can be easily
removed from the guide rails.
5. In order to fasten the selected sharpener in the
working position, from above push this into the
guide rails. Press the sharpener down until it
snaps into place.
The sharpeners also present a safety device.
Never use this device without a sharpener. Risk
of injury!
Operation
m Caution! Risk of injury!
• Always disconnect the plug from the mains socket
before working.
• Use only grinding disks and accessories recom-
mended by the manufacturer. The use of other in-
sertion tools and other accessories may cause risk
of injury.
• Never operate the device without the visual protec-
tion disk.
• Switch on the equipment only when it is safely in-
stalled on the work surface.
Despite spark protection, always wear safety
goggles while working in order to avoid eye in-
juries.
Keep your hands away from the grinding disc and
grinding belt when the device is in operation. In-
jury hazard!
Switching on and off
Ensure that the mains voltage matches the specifica-
tions on the rating plate.
Connect the equipment to the mains.
1. To switch on, press the "I" On switch and the device
starts up (see 3).
2. To switch off, press the "0" off switch and the de-
vice switches off (see 3).
After switching on the device, wait until the device
has reached its max. speed. Only then must you start
with the grinding.
m The disk will continue to run after the equipment is
switched off. There is a risk of injury.
Capítulos
Tabla de contenido
