Safety Regulations - EINHELL BM 190/JDD 200 Manual De Instrucciones

Anleitung BM 190-12 sprachig
GB
The main hazard zones on a woodworking
machine are:
the working area
the area directly adjacent to any moving parts of
the machine
the kick-back zone
4.I mportant notes
Please read this manual carefully and pay attention
to the information provided. Use this manual to
familiarize yourself with the machine, its correct use
and safety regulations.
m

Safety regulations

Important: Whenever electric tools are used it is
imperative to take basic safety precautions in
order to rule out risk of fire, electric shock and
injury, e.g.: Follow all these instructions before
and while you work with the saw.
Wear safety gloves whenever you carry out any
maintenance work on the blade.
When cutting with the table tilted, mount the
parallel fence to the right of the blade.
When cutting round wood, use a device to stop
the workpiece from twisting (see Figure 1).
When cutting boards in upright position, use a
device to prevent kick-back (see Figure 2).
A dust extraction system designed for an air
velocity of 20 m/s should be connected in order
to comply with woodworking dust emission
values and to ensure reliable operation.
In an emergency, switch off the machine directly
and pull out the power plug.
Keep these safety instructions in a safe place.
Always pull the plug out of the power socket
before adjusting or servicing the machine.
Give these safety regulations to all persons who
work on the machine.
Do not use this saw to cut fire wood.
Do not use this saw to cross-cut roundwood
unless you have a suitable holding device.
The machine is equipped with a safety circuit-
breaker to prevent it starting up again after
a voltage drop.
Before you use the machine for the first time,
check that the voltage marked on the rating plate
is the same as your mains voltage.
If you need to use an extension cable, make
sure its conductor cross-section is big enough
for the saw's power consumption. Minimum
cross-section: 1 mm 2 .
If you use a cable reel, the complete cable has
to be pulled off the reel.
Do not carry the machine by ist power cable.
Check the power cable . Never use a faulty or
damaged power cable.
12
16.10.2001 10:31 Uhr Seite 12
Never remove the plug from the socket-outlet by
pulling the cable. Protect the cable from heat, oil
and sharp edges.
Do not leave the saw in the rain and never use it
in damp or wet conditions.
Provide good lighting.
Never saw near combustible liquids or gases.
Wear suitable work clothes! Do not wear loose
garments or jewellery.
If you have long hair, wear a hair-net.
Avoid abnormal postures.
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allowed
to use the machine under supervision.
Do not allow other persons, particularly children,
to touch the tool or the power cable. Keep them
away from your workplace.
Keep children away from the machine when it is
connected to the power supply.
Keep your workplace clean of wood scrap and
any unnecessary objects.
Persons working on the machine should not be
distracted.
Note the direction of rotation of the motor and
saw blade.
After you have switched off the motor, never
slow down the saw blade by applying
pressure to its side.
Fit only blades which are well sharpened and
have no cracks or deformations.
Faulty saw blades have to be replaced
immediately.
Never use saw blades which do not comply with
the data specified in this manual.
It is imperative to make sure that all devices
which cover the saw blade are in good
working order.
Never dismantle the machine's safety devices
or put them out of operation.
Damaged or faulty safety devices have to be
replaced immediately.
Never cut workpieces which are too small to hold
securely in your hand.
Never load the machine so much that it cuts out.
Always press the workpiece firmly against the
saw table.
Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. - Pull
out the power plug! -
Conversions, adjustments, measurements and
cleaning jobs are to be performed only when the
motor is switched off. - Pull out the power plug! -
Before you switch on the machine, check that all
wrenches and adjustment tools have been
removed.
When you leave your workplace, switch off the
motor and pull out the power plug.