Tabla de contenido
Limitation of the amount of refrigerant to be charged
The above calculation result of the amount of refrigerant to be charged must become below the value in the table below.
Heat source unit model
Maximum amount of refrigerant
*1
kg [LBS]
Heat source unit model
Maximum amount of refrigerant
*1
kg [LBS] 55.0 [122]
Heat source unit model
Maximum amount of refrigerant
*1
kg [LBS]
Heat source unit model
Maximum amount of refrigerant
*1
kg [LBS] 62.0 [137]
*1: Amount of additional refrigerant to be charged on site
10.2. Precautions concerning piping
connection and valve operation
Conduct piping connection and valve operation accurately and carefully.
Removing the pinched connecting pipe
When shipped, a pinched connecting pipe is attached to the on-site high-
pressure/liquid and low-pressure/gas valves to prevent gas leakage.
Take the following steps 1 through 4 to remove the pinched connecting
pipe before connecting refrigerant pipes to the heat source unit.
1
2 Connect a charging hose to the service port on the low-pressure/
high-pressure liquid/gas refrigerant service valve, and extract the gas
in the piping between the refrigerant service valve and the pinched
3 After vacuuming gas from the pinched connecting pipe, sever the
pinched connecting pipe at the location shown in [Fig.10.2.1] and drain
the refrigerant.
4 After completing 2 and 3, heat the brazed section to remove the
pinched connecting pipe.
[Fig. 10.2.1] (P.11)
<A> Service valve for refrigerant
<B> Service valve for refrigerant
A
Shaft
B
Service port
C
Cap
D
Pinched connecting pipe severing portion
E
Pinched connecting pipe brazing portion
Warning:
The areas between the refrigerant service valves and the pinched
and refrigerant oil in that section before heating the brazed section.
refrigerant oil, the pipe may burst or the pinched connecting pipe may blow
off and ignite the refrigerant oil, causing serious injury.
Caution:
Place a wet towel on the refrigerant service valve before heating the brazed
Caution:
Refrigerant pipe connection
Check the high-pressure/low-pressure piping dimensions before connecting
the refrigerant pipe.
Refer to item 9.2 Refrigerant piping system for piping dimensions.
Make sure that the refrigerant pipe does not touch other refrigerants pipes,
unit panels, or base plates.
Use non-oxidative brazing when connecting pipes.
Do not burn the wiring and plate when brazing.
P72
P96
P120
22.0 [49]
28.5 [63]
29.5 [66]
P216S
P240S
P288S
56.0 [124]
67.5 [149]
P72
P96
P120
28.0 [62]
32.0 [71]
33.0 [73]
P216S
P240S
P288S
59.0 [131]
74.0 [164]
P144
P144S
P168
42.0 [93]
42.0 [93]
51.5 [114]
P312S
P336S
P360S
67.5 [149]
67.5 [149]
70.0 [155]
P144
P144S
P168
44.0 [98]
44.0 [98]
45.0 [100]
P312S
P336S
74.0 [164]
76.0 [168]
<Example of refrigerant piping connection>
[Fig.10.2.2] (P.11 - 12)
1
with heat source unit>
2
heat source unit>
3
source unit>
4
source unit>
5
with heat source unit>
6
with heat source unit>
7
heat source unit>
8
9
0
a
b
c
d
Sealing material for base leg
e
Sealing material for base leg
f
Sealing material for water panel
g
h
Sealing material for drain socket
<A> Front pipe routing
<B>
<C>
A
Shape
B
Without a low-pressure twinning pipe
C
D
Refrigerant service valve pipes
E
F
G
H
I
instructions included in the kit.
*2 Connection pipe is not used when the Twinning Kit is attached.
Pipe routing (for PQHY-P series)
: Use the included connecting pipe 3 to connect.
P72~P120
P144
connecting pipe 4 to connect.
: Use the included connecting pipe 4 to connect.
P168~P240
P72~P120
connecting elbow 1 to connect.
: Use the included connecting elbow 2 to connect.
P144~P240
Pipe routing (for PQRY-P series)
P72
connecting pipe 5 to connect.
: Use the included connecting pipe 5 to connect.
P96, P120
: Use the included connecting pipe 7 to connect.
P144~P240
P72~P120
connecting elbow 1 to connect.
: Use the included connecting pipe 6 to connect.
P144~P216
P240
connecting pipe 6 to connect.
P168S
P192
P192S
51.5 [114]
53.5 [118]
53.5 [118]
P168S
P192
P192S
45.0 [100]
52.0 [115]
50.0 [111]
*1, *2
31
Capítulos
Tabla de contenido
