Wheel Removal/Installation; Fuse Replacement - Nilfisk RS 501 Instrucciones De Uso

ENGLISH

WHEEL REMOVAL/INSTALLATION

Preliminary operations
Turn the ignition key (17, Fig. D) counterclockwise, to the end of stroke, then remove it.
1.
Engage the parking brake (7, Fig. E).
2.
Check that the machine cannot move with one wheel lifted (the parking brake operates only on the front wheels). If necessary
3.
keep the machine stationary by placing wedges on the wheels contacting the ground.
4. Remove the wheel according to the following procedure.
Front wheel removal/installation
Place a jack (1, Fig. AJ) under the relevant housing (2) on the machine side sill, in front of the wheel (3) to be removed.
5.
Loosen tire nuts before jacking.
6.
WARNING!
The jack (1, Fig. AJ) is not part of the machine equipment. Use a suitable jack with a minimum lifting capacity of
4,409 lb (2,000 kg).
Activate the jack (1, Fig. AJ) carefully, and lift the wheel (3) until it is slightly detached from the ground.
7.
8. Unscrew the mounting nuts and remove the wheel (3, Fig. AJ).
9. Install the wheel (3, Fig. AJ) by performing steps from 5 to 7 in the reverse order.
Wheel mounting nut tightening torque: 295 ft·lb (400 N·m).
Rear wheel removal/installation
Place a jack (1, Fig AK) under the relevant housing (4) in the rear axle (2), near the wheel to be removed.
10.
Loosen tire nuts before jacking.
11.
WARNING!
The jack (1, Fig. AK) is not part of the machine equipment. Use a suitable jack with a minimum lifting capacity of
4,409 lb (2,000 kg).
Activate the jack (1, Fig. AK) carefully, and lift the wheel (3) until it is slightly detached from the ground.
12.
Unscrew the mounting nuts and remove the wheel (3, Fig. AK).
13.
14. Install the wheel (3, Fig. AK) by performing steps from 9 to 11 in the reverse order.
Wheel mounting nut tightening torque: 295 ft·lb (400 N·m).

FUSE REPLACEMENT

Engage the parking brake (7, Fig. E).
1.
Turn the ignition key (17, Fig. D) counterclockwise, to the end of stroke, then remove it.
2.
Remove the transparent cover of the fuse box (24 or 25, Fig. D) and replace the relevant fuse:
3.
Fuse box B (24, Fig. D)
a) Hazard warning light fuse (10 A)
Brake light/horn fuse (10 A)
b)
c) Left side running light fuse (10 A)
d) Right side running light fuse (10 A)
e) Low beam fuse (15 A)
f) High beam fuse (15 A)
g) Cigarette lighter fuse (20 A)
h) Free fuse holder
Fuse box A (25, Fig. D)
Hydraulic system oil cooler fan/skirt solenoid valve fuse (20 A)
i)
j) Fuel solenoid valve fuse (10 A)
k) Cab blower/flashing light/windscreen wiper fuse (15 A)
l) Dust control system water pump fuse (10 A)
Dust control system water pump/climate control system (optional) fuse (20 A)
m) Reverse gear buzzer fuse (10 A)
n) Warning lights/glow plug control unit fuse (10 A)
Electric jack warning light fuse (10 A)
o)
Hopper panel opening/closing electric jack fuse (15 A)
p)
Install the transparent cover of the fuse box (24 or 25, Fig. D).
4.
32
INSTRUCTIONS FOR USE
33015498(3)2008-02 RS 501