Using The Rear Suction Pipe (*); Using The Windscreen Wiper/Washer; Using The Cab Heating; Using The Cab Climate Control System (*) - Nilfisk RS 501 Instrucciones De Uso

ENGLISH

USING THE REAR SUCTION PIPE (*)

(*) Optional for some countries.
To collect dust/debris with the rear suction pipe (22, Fig. G), rather than the suction inlet (10), perform the following procedure.
As shown in the Hopper Dumping paragraph, lift the hopper for 4÷6 in (10÷15 cm) approximately, then turn off the engine.
1.
2. Open the right panel door (16, Fig. G).
There is a heavy rubber flap (2, Fig. I) attached to the hopper just above the debris opening on the front face of the hopper.
3.
This flap (2) needs to rotate down to cover the hole (3, Fig. I). To do this, pull the top edge of the flap off of its retaining screw
(1) and allow the flap (2) to rotate into place over the hopper hole (3).
Lower the hopper completely, as explained in the Hopper Dumping paragraph.
4.
Turn off the engine and engage the parking brake with the lever (7, Fig. E).
5.
6. Disengage the fasteners (25, Fig. G) of the rear suction pipe (22).
Open the suction pipe closing panel by lifting the knob (1, Fig. J) until the end of stroke, as shown in the figure, then screw the
7.
knob (1) to secure it in that position.
8. Start the engine as shown in the relevant paragraph.
Check that the hopper (12, Fig. G) is lowered and that the warning light (26, Fig. D) is off.
9.
10. Gradually bring forward the engine throttle lever (16, Fig. E) and set the engine speed on the display (11, Fig. D) to the
following value:
• minimum 1,800 rpm
maximum 2,500 rpm
•
11. Turn on the suction fan with the lever (14, Fig. E).
Disengage the parking brake with the lever (7, Fig. E).
12.
Disengage the bands (25, Fig. G) and pick up the rear suction pipe (22, Fig. G).
13.
Pull the pin (1, Fig. K) and turn the handle (2) to the position shown in the figure. Hold the lever in this position by releasing the
14.
pin (1) and ensure that the pin is inserted in the relevant housing.
To use the dust control system water jet, open the valve (3, Fig. K) by turning it in the position shown in the figure.
15.
With the help of an assistant, start to collect debris with the rear suction pipe (4, Fig. K), by grasping it as shown in the figure.
16.
While working, the machine picks up both light materials such as dust, paper, leaves, etc. and heavy materials such as
•
stones, bottles, etc.
17. To restore the machine operation with the suction inlet (10, Fig. G), perform the steps from 1 to 15 in the reverse order.

USING THE WINDSCREEN WIPER/WASHER

Press the switch (20, Fig. D) to sprinkle the detergent on the windscreen.
1.
2. Press the switch (20, Fig. D) to start and stop the windscreen wiper.

USING THE CAB HEATING

To turn on the cab heating, turn the knob (15, Fig. E) counterclockwise as necessary.
1.
2. Choose one of the two blower speed with the switch (21, Fig. D).
To turn off the cab heating, turn off the blower with the switch (21, Fig. D) and turn the knob (15, Fig. E) clockwise to the end of
3.
stroke.

USING THE CAB CLIMATE CONTROL SYSTEM (*)

(*) Optional for some countries.
To turn on the climate control system, turn the switch (18, Fig. D) to the first position, which activates the first blower speed.
1.
2. To activate the second blower speed, turn the switch (18, Fig. D) to the second position.
3. To turn off the climate control system, turn the switch (18, Fig. D) to the original position.
18
INSTRUCTIONS FOR USE
33015498(3)2008-02 RS 501