DeWalt DCS727 Manual De Instrucciones página 49

Description (Fig. A1, A2, C–F)

WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
Fig. A1
Lower guard
1
Operating handle
2
3 Carrying handle
Battery
4
Battery release button
5
Rail lock knob
6
Rail set screw adjustment
7
Date code
8
Rails
9
Bevel scale
10
Lock down pin
11
Fence adjustment knob
12
Sliding fence
13
Base fence
14
Base extension/carry handle
15
16 Hand indentation
Table
17
Bench mounting holes
18
Mitre scale
19
20 Dust duct inlet
Mitre lock handle
21
Mitre latch button
22
Kerf plate
23
Fig. A2
Intended Use
Your D WALT DCS727 mitre saw has been designed for professional
e
cutting of wood, wood products and plastics. When using the appropriate
saw blades, sawing aluminium is also possible. It performs the sawing
operations of cross-cutting, bevelling and mitring easily, accurately
and safely.
DO nOT use under wet conditions or in the presence of flammable liquids
or gases.
This mitre saw is a professional power tool.
DO nOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
• Young children and the infirm. This appliance is not intended for use
by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are supervised by a person
responsible for their safety. Children should never be left alone with
this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can cause injury.

WARNING: Use only D WALT battery packs and chargers.
e
Inserting and Removing the Battery Pack from the
Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 4 with the rails inside the tool's handle (Fig. B).
Trigger switch
24
Lock-off lever
25
Padlock hole
26
27 XPS™ temporary on switch
Wing nut
28
Depth adjustment screw
29
Grooving stop
30
Blade wrench
31
Base
32
Bevel lock knob
33
0° bevel stop
34
Right-hand flip down stop
35
Dust port
36
Belt cover
37
Mitre detent override
38
Optional accessories
Fig. C
DWS5026-XJ Workpiece clamp
39
Fig. D
DW7053-QZ Dustbag
40
Fig. E
DE7023-XJ / DE7033-XJ Leg
41
stand
Fig. F
DE7025-XJ Clamp brackets
42
4 is fully charged.
2. Slide it into the handle until the battery pack is firmly seated in the tool
and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 5 and firmly pull the battery pack out of the
tool handle.
2. Insert battery pack into the charger as described in the charger section
of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists of
e
three green LED lights that indicate the level of charge remaining in the
battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
combination of the three green LED lights will illuminate designating the
level of charge left. When the level of charge in the battery is below the
usable limit, the fuel gauge will not illuminate and the battery will need to
be recharged.
nOTE: The fuel gauge is only an indication of the charge left on the battery
pack. It does not indicate tool functionality and is subject to variation based
on product components, temperature and end-user application.
Unpacking (Fig. A1, G)
1. Open the box and lift the saw out by the con venient carrying handle
as shown in Figure G.
2. Place the saw on a smooth, flat surface.
3. Release the rail lock knob , and push the saw head back to lock it in
6
the rear position.
4. Press down lightly on the operating handle
down pin 11 .
5. Gently release the downward pressure and hold the operating handle,
allowing it to rise to its full height.
Bench Mounting (Fig. A1)
Holes 18 are provided in all four feet to facilitate bench mounting. Two
different-sized holes are provided to accommodate different sizes of screws.
Use either hole; it is not necessary to use both.
Always mount your saw firmly to a stable surface to prevent movement.
To enhance the tool's portability, it can be mounted to a piece of 12.7 mm
or thicker plywood which can then be clamped to your work support or
moved to other job sites and reclamped.
nOTE: If you elect to mount your saw to a piece of plywood, make sure that
the mounting screws don't protrude from the bottom of the wood. The
plywood must sit flush on the work support. When clamping the saw to
any work surface, clamp only on the clamping bosses where the mounting
screw holes are located. Clamping at any other point will interfere with the
proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be sure the mounting
surface is not warped or otherwise uneven. If the saw rocks on the
surface, place a thin piece of material under one saw foot until the saw
sits firmly on the mounting surface.
Assembling the Base Extensions (Fig. Z)

WARNING: Base extensions must be assembled to both sides of
the saw's base before using the saw.

WARNING: Be sure to adjust the base extensions using the
mounting holes so they are level with the saw's base.
1. Locate the holes above the hand indentations
the base.
2. Using the supplied wrench or a T30 wrench, attach the screw
through the washer , through the base extension
64
holes on the base.
3. Ensure the extension is secure by pulling on the extension to verify
no movement.
4. Repeat steps 1 through 3 on the other side.
EnGLIsh
. A
61
3 ,
and pull out the lock
2
16 on the side of
63
, and into the
15
47