Safety Instructions For Batteries; Technical Data - REMS Power-Press E Instrucciones De Servicio

eng

Safety instructions for batteries

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
● Batteries may only be used at battery or ambient temperatures of –10 °C – +60
°C (14 °F – +140 °F).
● The rapid charger may only be used at rapid charger or ambient temperatures
of 0 °C – +40 °C (32 °F – +104 °F).
● Observe the safety instructions printed on the battery and the charger.
● Do not throw defective batteries in the normal household waste. Hand the defec-
tive batteries over to an authorised REMS contract service workshop or a
recognised disposal company.
● Protect battery from getting wet.
● Cover the battery contacts when storing outside the tool or rapid charger.
● Do not open the battery. Danger of explosion and fire due to short-circuit.
● Do not modify the construction of the battery.
● Only use the battery indoors.
● Do not use the battery in adverse ambient conditions, e.g. flammable gases,
solvents, dust, fumes, wet.
● Do not use the battery if the housing or contacts are damaged.
● Do not use the battery in areas where there is a danger of explosion.
● Observe the safety instructions printed on the battery and the charger.
Explanation of symbols
Read the operating instructions before use
Power tool complies with protection class I
Power tool complies with protection class II
The tool is not suitable for using outdoors
Environmentally friendly disposal

1. Technical Data

Intended use
WARNING
REMS radial presses are intended for the purpose of making press joints of all
common pressfitting systems.
REMS cropping tongs are intended for the purpose of cropping threaded bars up to
the strength class 4.8 (400 N/mm²).
REMS cable shears are intended for the purpose of cropping electric cables
≤ 300 mm² (Ø 30 mm).
REMS axial presses are intended for the purpose of making compression sleeve
connections.
REMS pipe expanders are intended for the purpose of expanding and calibrating
pipes.
REMS batteries are intended for the purpose of supplying energy to REMS battery-
operated machines.
REMS chargers are intended for the purpose of charging the REMS batteries.
All other uses are not for the intended purpose and are prohibited.
1.1. Article numbers
REMS Power-Press E drive unit
REMS Power-Press drive unit
REMS Power-Press ACC drive unit
REMS Mini-Press ACC drive unit Li-Ion
REMS Akku-Press drive unit Li-Ion
REMS Akku-Press ACC drive unit Li-Ion
REMS Ax-Press 25 ACC drive unit Li-Ion
REMS Ax-Press 25 L ACC drive unit Li-Ion
REMS Ax-Press 40 drive unit Li-Ion
REMS Akku-Ex-Press Cu ACC drive unit Li-Ion
REMS Akku-Ex-Press P drive unit Li-Ion
REMS Akku-Ex-Press P ACC drive unit Li-Ion
REMS Akku-Ex-Press Q & E ACC drive unit Li-Ion
REMS Power-Ex-Press Q & E ACC drive unit
Expanding device 6 – 40 mm, ½ – 1½"
Expanding device 54 – 63 mm, 2"
REMS battery Li-Ion 14.4 V, 1.6 Ah
REMS battery Li-Ion 14.4 V, 3.2 Ah
REMS rapid charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
REMS voltage supply Li-Ion 230 V, , for 14.4 V batteries
Sheet steel case, REMS Power-Press E
Sheet steel case, REMS Power-Press
Sheet steel case, REMS Power-Press ACC
Sheet steel case, REMS Mini-Press ACC
Sheet steel case, REMS Akku-Press / REMS Akku-Press ACC
Sheet steel case, REMS Ax-Press 40
Sheet steel case, REMS Akku-Ex-Press Q & E
Sheet steel case, REMS Ax-Press 25 ACC and Ax-Press 25 L ACC 573284
Sheet steel case, REMS Akku-Ex-Press Cu ACC
Sheet steel case, REMS Akku-Ex-Press P / Akku-Ex-Press P ACC
Sheet steel case, Combi Set REMS Ax-Press 25 ACC
and Akku-Ex-Press P ACC
1.2. Capacity
REMS Mini-Press ACC Radial press for making press joints in all
standard press fitting systems on steel pipes, stainless steel
pipes, copper pipes, plastic pipes, composite pipes
Radial presses REMS Power-Press and REMS Akku-Press for
making press joints in all standard press fitting systems
on steel pipes, stainless steel pipes, copper pipes,
plastic pipes, composite pipes
Axial presses for making compression sleeve joints (sliding
sleeve joints) on stainless steel pipes, steel pipes, copper
pipes, plastic pipes, composite pipes
REMS Akku-Ex-Press Q & E ACC for expanding of
pipes/coil for the system Uponor Quick & Easy
REMS Power-Ex-Press Q & E ACC for expanding of
pipes/coil for the System Uponor Quick & Easy
REMS Akku-Ex-Press Cu ACC for expanding and
calibrating copper pipes
REMS Akku-Ex-Press P and REMS Akku-Ex-Press P ACC
for widening plastic pipes
Operating temperature range
REMS cordless presses
Battery
Rapid charger
Mains operated presses
1.3. Thrust / pressing power
Thrust of radial presses
Pressing power of radial presses
Thrust of radial press Mini
Pressing power of radial press Mini
Pressing power REMS Ax-Press 40
Pressing power REMS Ax-Press 25 ACC
Pressing power REMS Ax-Press 25 L ACC
Pressing power REMS Akku-Ex-Press Cu ACC
Pressing power REMS Akku-Ex-Press P
Pressing power REMS Akku-Ex-Press P ACC
REMS Akku-Ex-Press Q & E ACC
REMS Power-Ex-Press Q & E ACC
1.4. Electric Data
REMS Power-Press E,
REMS Power-Press,
REMS Power-Press ACC,
REMS Power-Ex-Press Q & E ACC
REMS Akku-Press, Akku-Press ACC
Ax-Press 40
REMS Akku-Ex-Press Q & E,
REMS Mini-Press ACC,
572100
REMS Ax-Press 25 ACC / 25 L ACC,
577001
REMS Akku-Ex-Press Cu ACC,
577000
REMS Akku-Ex-Press P
578001
REMS Akku-Ex-Press P ACC
571003
571004
Rapid charger
573003
Li-Ion/Ni-Cd
573004
573006
575006
575009
575008
Voltage supply
575005
575007
575100 1.5. Dimensions
575101 REMS Power-Press E
571545 REMS Power-Press,
571555 REMS Power-Press ACC
REMS Mini-Press ACC
571560
REMS Akku-Press / Akku-Press ACC
571565
REMS Ax-Press 40
570280
REMS Akku-Ex-Press Q & E ACC
570280
REMS Power-Ex-Press Q & E ACC
570280
578290 REMS Ax-Press 25 ACC
571290 REMS Ax-Press 25 L ACC
573282 REMS Akku-Ex-Press Cu ACC
578290 REMS Akku-Ex-Press P
REMS Akku-Ex-Press P ACC
Ø 10 – 40 mm
Ø 10 – 108 mm
Ø 12 – 40 mm
Ø 16 – 40 mm
Ø 16 – 63 mm
Ø 12 – 40 mm
–10 °C – +60 °C (14 °F – +140 °F)
–10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +104 °F)
–10 °C – +60 °C (14 °F – +140 °F)
230 V 1~; 50 – 60 Hz; 450 W; 1,8 A
110 V 1~; 50 – 60 Hz; 450 W
S3 20% (AB 2/10 min)
all-insulated,
interference-suppressed
14.4 V =; 3.2 Ah; 20 A
14.4 V =; 1.6 Ah
14.4 V =; 3.2 Ah
Input 230 V~; 50 – 60 Hz; 65 W
14.4 – 18 V – ---
Output
Input 100 – 120 V~; 50 – 60 Hz; 65 W
14.4 – 18 V – ---
Output
Input 230 V~; 50 – 60 Hz
14.4 V – ---; 6 A – 33 A
Output
430×110×85 mm (16.9"×4.3"×3.3")
365×235×85 mm (14.4"×9.2"×3.3")
288×260×80 mm (11.3"×10.2"×3.1")
338×290×85 mm (13.3"×11.4"×3.3")
330×320×85 mm (13"×12.6"×3.3")
290×260×80 mm (11,4"×10,2"×3,1")
420×245×81 mm (16,5"×9,6"×3,2")
295×260×80 mm (11,6"×10,2"×3,3")
325×260×80 mm (12,8"×10,2"×3,1")
265×260×80 mm (10,4"×10,2"×3,1")
275×260×80 mm (10,8"×10,2"×3,1")
275×260×80 mm (10,8"×10,2"×3,1")
eng
573284
573284
573284
Ø ⅜ – 1½"
Ø ½ – 2"
Ø 8 – 42 mm
Ø ⅜ – 1¾"
32 kN
100 kN
22 kN
70 kN
30 kN
20 kN
13 kN
20 kN
20 kN
20 kN
20 kN
34 kN