Noise Information; Preparations For Use; Electrical Connection - REMS Power-Press E Instrucciones De Servicio

eng
1.6. Weights
REMS Power-Press E drive unit
REMS Power-Press drive unit
REMS Power-Press ACC drive unit
REMS Mini-Press ACC drive unit without battery
REMS Akku-Press / Akku-Press ACC drive unit
without battery
REMS Ax-Press 40 drive unit without battery
REMS Akku-Ex-Press Q & E ACC drive unit without batt. 2.0 kg
REMS Power-Ex-Press Q & E ACC drive unit without batt. 5.6 kg
REMS Ax-Press 25 ACC drive unit without battery
REMS Ax-Press 25 L ACC drive unit without battery
REMS Akku-Ex-Press Q & E ACC drive unit without batt. 2.0 kg
REMS Power-Ex-Press Q & E ACC drive unit
REMS Akku-Ex-Press Cu ACC drive unit without battery
REMS Akku-Ex-Press P drive unit without batt.
REMS Akku-Ex-Press P ACC drive unit without battery
REMS battery Li-Ion 14.4 V, 1.3 Ah
REMS battery Li-Ion 14.4 V, 2.2 Ah
Pressing tongs (average)
Pressing tongs Mini (average)
Pressing heads (pair, average)
Expanding head (average)
Adapter tong Z2
Adapter tong Z4
Adapter tong Z5
Pressing ring M54 (PR-3S)
Pressing ring U75 (PR-3B)

1.7. Noise information

Emission at workplace
REMS Power-Press E
REMS Power-Press /
Power-Press ACC
REMS Mini-Press ACC
REMS Akku-Press, Akku-Press ACC L
REMS Ax-Press 40
REMS Ax-Press 25 ACC / 25 L ACC L
REMS Akku-Ex-Press Q&E ACC
REMS Power-Ex-Press Q&E ACC L
REMS Akku-Ex-Press Cu ACC
REMS Akku-Ex-Press P
REMS Akku-Ex-Press P ACC
1.8. Vibrations
Weighted effective value of acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
Attention: The indicated weighted effective value of acceleration can differ during
operation from the indicated value, dependent on the manner in which the device
is used. Dependent upon the actual conditions of use (periodic duty) it may be
necessary to establish safety precautions for the protection of the operator.

2. Preparations for Use

The respective latest sales literature applies for the use of REMS pressing
tongs, REMS pressing tongs Mini, REMS pressing rings, REMS adapter tongs,
REMS pressing heads and REMS expanding heads for the different pipe
connection systems. If the system manufacturer alters components of pipe
connection systems or markets new ones, their current application status must
be enquired about at REMS (Fax +49 7151 17 07 - 110).

2.1. Electrical connection

WARNING
Note the mains voltage! Before connecting the drive unit or the rapid charger,
check whether voltage on the rating plate matches the mains voltage. At work
sites, in damp surroundings, in the open or in the case of comparable types of
use, only operate the equipment off the mains using a 30 mA fault current
protected switch (FI breaker).
Rechargeable batteries
NOTICE
Always hold the battery upright when inserting it in the drive unit or the rapid
charger. If inserted at an angle it can cause damage to the contacts and result
in a short circuit which damages the battery.
Total discharging by undervoltage
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by "total discharge". The cells of the REMS Li-Ion
battery are delivered pre-charged to approx. 40 %. Therefore the Li-Ion batteries
must be charged before use and recharged regularly. Failure to observe this
regulation of the cell manufacturer can lead to damage to the Li-Ion battery by
total discharging.
4.4 kg (9.6 lb)
4.6 kg (10.0 lb)
4.6 kg (10.0 lb)
2.1 kg (4.5 lb)
3.8 kg (8.3 lb)
5.4 kg (11.8 lb)
(4.4 lb)
(12.2 lb)
2.6 kg (5.6 lb)
2.8 kg (6.1 lb)
(4.4 lb)
5.6 kg (12.2 lb)
2,3 kg (5,0 lb)
2.0 kg (4.3 lb)
2.0 kg (4.3 lb)
0.3 kg (0.6 lb)
0.5 kg (1.1 lb)
1.8 kg (3.9 lb)
1.2 kg (2.6 lb)
0.3 kg (0.6 lb)
0.2 kg (0.4 lb)
2.0 kg (4.8 lb)
3.6 kg (7.8 lb)
3.8 kg (8.2 lb)
3.1 kg (6.7 lb)
2.7 kg (5.9 lb)
L = 76 dB L = 87 dB K = 3 dB
pA WA
L = 81 dB L = 92 dB K = 3 dB
pA WA
L = 73 dB L = 84 dB K = 3 dB
pA WA
= 74 dB L = 85 dB K = 3 dB
pA WA
L = 74 dB L = 85 dB K = 3 dB
pA WA
= 73 dB L = 84 dB K = 3 dB
pA WA
L = 73 dB L = 84 dB K = 3 dB
pA WA
= 81 dB L = 92 dB K = 3 dB
pA WA
L = 73 dB L = 84 dB K = 3 dB
pA WA
L = 73 dB L = 84 dB K = 3 dB
pA WA
L = 73 dB L = 84 dB K = 3 dB
pA WA
< 2,5 m/s² K = 1,5 m/s²
Total discharging due to storage
If a relatively low charged Li-Ion battery is stored, self discharging can lead to
total discharge damage of the battery after longer storage. Li-Ion batteries must
therefore be charged before storing and recharged every six months at the
latest and charged again before use.
NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid
their total discharge. The rechargeable battery will be damaged by total
discharge.
1
Only use a REMS rapid charger for charging. New Li-Ion batteries and Li-Ion
batteries which have not been used for a long time only reach full capacity after
several charges. Non-rechargeable batteries may not be charged.
Battery charging status check for all Li-Ion cordless presses
All REMS cordless presses made as of 2011-01-01 are equipped with an
electronic battery charging status check with battery charge indication by a
2-coloured green/red LED (23). The LED lights green when the battery is fully
or still sufficiently charged. The LED lights red when the battery must be charged.
If this condition occurs during pressing and the pressing process is not finished,
the pressing must be completed with a fully charged Li-Ion battery. If the drive
unit is not used, the LED goes out after approx. 2 hours but comes on again
when the drive unit is switched back on.
Rapid charger Li-ion/NiCd (Art. No. 571560)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the rapid charger, the green control lamp
flashes to indicate that the battery is charging. The green light stops flashing
and remains on to signal that the battery is fully charged. If the red control lamp
flashes, the battery is defective. If the red control lamp comes on and remains
on, this indicates that the temperature of the rapid charger and / or the battery
is outside the permissible range of 0°C to +40°C.
NOTICE
The rapid chargers are not suitable for outdoor use.
2.2. Installing (changing) the pressing tong, pressing tong Mini (1), the pressing
ring with adapter tong (Fig. 18) in radial presses (Fig. 1, 16 and 17)
Pull out the mains plug or remove the battery. Only use pressing tongs, pressing
tongs Mini or pressing rings with system-specific pressing contour according
to the pressfitting system to be pressed. Pressing tongs, pressing tongs Mini
or pressing rings have letters on the pressing jaws or pressing segments to
identify the pressing contour and a number to identify the size. Read and follow
the installation and assembly instructions of the system manufacturer. The
REMS adapter tongs are also identified by a letter and a number. This identi-
fication serves to assign them to the permissible REMS pressing ring. Never
use non-matching pressing tong, pressing tong Mini, pressing ring and adapter
tong (pressing contour, size). The press joint could be rendered useless and
the machine and pressing tong, pressing tong Mini, pressing ring and adapter
tong could be damaged.
It is best to place the drive machine on a bench or on the floor. The pressing
tong, pressing tong Mini or adapter tong can only be installed (changed) when
the press rollers (5) are fully retracted. If necessary, in the case of the REMS
Power-Press E, set the rotation direction lever (7) to the left and operate the
inching switch (8), and in the case of the REMS Mini-Press, REMS Power-Press
and REMS Akku-Press press the reset button (13) until the press rollers (5)
are fully retracted.
Open the tongs shank (2). To do so, press the locking pin (4), the tongs shank
(2) jumps out under spring loading. Insert the selected pressing tong, pressing
tong Mini (1) or adapter tong (19). Push forward the tong retaining bolt (2) until
the locking pin (4) snaps into place. Press down the pressure plate (3) directly
over the tong retaining bolt. Do not start radial presses without pressing tong,
pressing tong Mini or pressing ring with adapter tong inserted. Only start the
pressing process to make a press joint. Without pressing counterpressure by
the press fitting the drive machine or pressing tong, pressing tong Mini, pressing
ring and adapter ring will be exposed to unnecessarily high stress.
CAUTION
Never operate press when the tongs shank (2) is not locked. Risk of
fracture!
2.3. Installing (changing) the pressing heads (14) in axial presses
(Figs. 7, 10)
Remove the battery. Only use system-specific pressing heads. REMS press i ng
heads have a letter to identify the compression sleeve system and a number
to identify the size. Consult and comply with the instructions for installation and
fitting of the system's manufacturer. Never use non-matching pressing heads
(compression sleeve system, size) for pressing work. The press joint could be
unserviceable, and both the machine and the press ing heads might be damaged.
Push the selected pressing heads (14) right in, if necessary turning them until
they engage (ball catch). Keep the pressing heads and locating hole inside the
pressing device clean.
2
eng