Safety Instructions For Batteries; Technical Data; Scope Of Supply - REMS Curvo Instrucciones De Servicio

eng
● Check the power cable of the power tool and extension leads regularly for
damage. Have these renewed by qualifi ed experts or an authorised REMS
customer service workshop in case of damage.
● Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
● REMS bending spray in spray cans contains environmentally friendly but
highly infl ammable propellant gas (butane). Aerosol cans are pressurised;
do not open by force. Protect them against direct sunlight and temperatures
above 50°C. The aerosol cans can burst, risk of injury.

Safety Instructions for Batteries

WARNING
Read all the safety notes, instructions, illustrations and technical data which
come with this power tool. Failure to heed the following instructions can lead to
electric shock, fi re and/or severe injuries.
Save all warnings and instructions for future reference.
● Only use the battery in REMS power tools. Only then is the battery safe from
dangerous overloading.
● Only use original REMS batteries with the voltage specifi ed on the rating
plate. Using other batteries can lead to injuries and risk of fi re due to exploding
batteries.
● Use the REMS battery and the rapid charger only in the specifi ed operating
temperature range.
● Only recharge REMS batteries in the REMS rapid charger There is a risk of Only recharge REMS batteries in the REMS rapid charger There is a risk of Only recharge REMS batteries in the REMS rapid charger
fi re if an unsuitable battery charger is used.
● Charge the REMS battery to full capacity with the rapid charger before using
for the fi rst time. Batteries are delivered partly charged.
● Insert the REMS battery into the battery compartment straight and without
force. There is a risk of bending the battery contacts and damaging the battery.
● Protect the batteries against heat, sunlight, fi re, moisture and wet. There is
a risk of explosion and fi re.
● Do not use the batteries in areas where there is a risk of explosion and in
the vicinity of infl ammable gases, solvents, dust, fumes, liquids for example.
There is a risk of explosion and fi re.
● Do not open the battery or modify its construction. There is a risk of explosion
and fi re due to short-circuiting.
● Do not use batteries with damaged housings or damaged contacts. Damage
to or improper use of the battery can cause fumes to escape. The fumes can
irritate the respiratory tracts. Let in fresh air and consult a doctor in case of
symptoms.
● Fluid can leak from the battery when used improperly. Do not touch the
fl uid. Leaking fl uid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the fl uid gets into the eyes.
● Observe the safety instructions on the battery and the rapid charger.
● Keep the unused battery away from paper clips, coins, keys, nails, screws
or other small metal objects which could cause bridging of the contacts.
There is a risk of explosion and fi re due to short-circuiting.
● Remove the battery before stowing/storing the power tool for long periods
of time. Protect the battery contacts against short-circuiting, e.g. with a cap. This
reduces the risk of fl uids escaping from the batteries.
● Do not throw defective batteries in the normal household waste. Hand the
defective batteries over to an authorised REMS contract service workshop or a
recognised disposal company. Observe the national regulations. See also page
6. Disposal.
● Keep batteries out of reach of children. Batteries can be life threatening if
swallowed, seek medical assistance immediately.
● Avoid contact with leaking batteries. Leaking fl uid can cause skin irritation
and burns. Rinse off immediately with water in case of contact. Also consult a
doctor if the fl uid gets into the eyes.
● Take the batteries out of the power tool when they are empty. This reduces
the risk of fl uids escaping from the batteries.
● Never recharge the non-rechargeable batteries, open them, throw them on
fi res or create a short-circuit. The batteries can cause fi res and burst. There
is a risk of injury.
Explanation of symbols
WARNING Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION CAUTION Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use ear protection
Power tool complies with protection class II
Environmentally friendly disposal
CE conformity mark
REMS Curvo / REMS Curvo 50 / REMS Akku-Curvo

1. Technical Data

Use for the intended purpose
WARNING
REMS Curvo and REMS Akku-Curvo are intended for the purpose of cold draw
bending of pipes up to 180°.
REMS Curvo 50 is intended for cold draw bending of pipes up to 90°.
All other uses are not for the intended purpose and are prohibited.

1.1. Scope of Supply

REMS Curvo: Electric pipe bending machine, insert bolts, bending
formers and back formers according to ordered set,
instruction manual, steel case.
REMS Curvo 50: Electric pipe bending machine, square driver 35 – 50,
support 35 – 50, insert bolt, instruction manual,
transport crate.
REMS Akku-Curvo: Cordless pipe bending machine, Li-Ion battery, rapid
charger Li-Ion/Ni-Cd, insert bolt, bending formers and
back formers according to ordered set, instruction
manual, steel case.
1.2. Article numbers
REMS Curvo drive unit
REMS Curvo 50 drive unit
REMS Akku-Curvo Li-Ion drive unit
Square driver 35 – 50, support 35 – 50 (REMS Curvo 50)
Square driver 10 – 40, support 10 – 40 (REMS Curvo 50)
Insert bolt
Rapid charger Li-Ion/Ni-Cd (REMS Akku-Curvo)
Li-Ion 18 V, 3.0 Ah battery (REMS Akku-Curvo)
REMS bending spray, 400 ml
Machine holder 3B
Machine holder WB
Steel case (REMS Curvo)
Steel case (REMS Akku-Curvo)
Transport crate (REMS Curvo 50)
Steel case (bending former and back former of REMS Curvo 50)
REMS CleanM
Bending formers and back formers
1.3. Applications
No cracks or wrinkles shall occur during professional cold bending. Pipe
qualities and sizes which do not guarantee this are not suited to be bent with
REMS Curvo, REMS Curvo 50 and REMS Akku-Curvo.
Hard copper pipes are cold bendable up to Ø 18 mm according to DIN EN
1057, minimum radii must be complied with. Bending formers and back formers
for larger bending radii can be supplied.
REMS Curvo
● Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 35 mm, Ø ⅜ –1⅜".
● Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
● Stainless steel pipes of the pressfi tting systems Ø 12 – 28 mm.
● Jacketed C-steel pipes of the pressfi tting systems Ø 12 – 28 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Steel pipes DIN EN 10255 (DIN 2440) Ø ¼" – ¾".
● Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
● Composite pipes Ø 14 – 40 mm.
Largest bending angle
REMS Curvo 50
● Steel pipes as per DIN EN 10255 (DIN 2440) Ø ¼" – 1¼".
● Hard, half-hard and soft copper tubes Ø 10 – 42 mm.
● Thin walled copper tubes Ø 10 – 35 mm.
● Stainless steel tubes of pressfi tting systems Ø 12 – 42 mm.
● (Jacketed) C-steel pipes of the pressfi tting systems Ø 12 – 42 (28) mm.
● Composite tubes Ø 14 – 50 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
Largest bending angle
REMS Akku-Curvo
● Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 28 mm, Ø ⅜ – 1⅛".
● Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
● Stainless steel pipes of the pressfi tting systems Ø 12 – 28 mm.
● Jacketed C-steel pipes of the pressfi tting systems Ø 12 – 28 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Steel pipes DIN EN 10255 (DIN 2440) Ø ¼ – ½".
● Electrical installation pipes DIN EN 50086 Ø 16 – 25 mm.
● Composite pipes Ø 14 – 32 mm
Largest bending angle
1.4. Speed Curvo
Speed infi nitely
adjustable 0...4 min‫¹־‬
eng
580000
580100
580002
582110
582120
582036
571560
565225
140120
586100
586150
586000
586015
590160
586012
140119
see Fig. 3
180°
90°
180°
Curvo 50 Akku-Curvo
0...1 min‫¹־‬ 0...3,33 min‫¹־‬
11