Makita DLS110 Manual De Instrucciones página 26

Ocultar thumbs Ver también para DLS110:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 130
Securing workpiece
WARNING:
It is extremely important to always
secure the workpiece correctly with the proper
type of vise or crown molding stoppers. Failure to
do so may result in serious personal injury and cause
damage to the tool and/or the workpiece.
WARNING:
After a cutting operation do not
raise the blade until it has come to a complete
stop. The raising of a coasting blade may result in
serious personal injury and damage to the workpiece.
WARNING:
When cutting a workpiece that
is longer than the support base of the saw, the
material should be supported the entire length
beyond the support base and at the same height
to keep the material level. Proper workpiece support
will help avoid blade pinch and possible kickback
which may result in serious personal injury. Do not
rely solely on the vertical vise and/or horizontal vise
to secure the workpiece. Thin material tends to sag.
Support workpiece over its entire length to avoid
blade pinch and possible KICKBACK.
► Fig.41: 1. Support 2. Turn base
Guide fences
WARNING:
Before operating the tool, make
sure that the upper fence is secured firmly.
WARNING:
Before bevel-cutting, make sure
that no part of the tool, especially the blade, con-
tacts the upper and lower fences when fully low-
ering and raising the handle in any position and
while moving the carriage through its full range
of travel. If the tool or blade makes contact with
the fence this may result in kickback or unexpected
movement of the material and serious personal injury.
Use upper fences to support the material higher than
the lower fences. Insert the upper fence into the hole on
the lower fence and tighten the clamping screw.
► Fig.42: 1. Upper fence 2. Lower fence 3. Clamping
screw 4. Adjusting screw
NOTICE:
The lower fences are fixed to the base in
the factory. Do not remove the lower fences.
NOTICE:
If the upper fence is still loose after tight-
ening the clamping screw, turn the adjusting screw to
close a gap. The adjusting screw is factory adjusted.
You don't need to use it unless needed.
You can store the upper fences onto the holder when
not in use. Use the clip on the upper fence to hold it on
the holder.
► Fig.43: 1. Holder 2. Upper fence 3. Clip
Vertical vise
WARNING:
firmly against the turn base and guide fence with
the vise during all operations. If the workpiece is
not properly secured against the fence the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
personal injury.
► Fig.44: 1. Vise arm 2. Vise rod 3. Clamping screw
4. Vise knob
The vertical vise can be installed in two positions on
either the left or right side of the base. Insert the vise
rod into the hole in the base.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. If the clamping screw contacts
the carriage, install it on the opposite side of vise arm.
Make sure that no part of the tool contacts the vise
when lowering the handle all the way. If some part
contacts the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
NOTE: For a quick setting of workpiece, turning the
vise knob to 90° counterclockwise allows the vise
knob to be moved up and down. To secure the work-
piece after setting, turn the vise knob clockwise.
Horizontal vise
Optional accessory
WARNING:
wise until the workpiece is properly secured. If
the workpiece is not properly secured the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
personal injury.
WARNING:
such as base boards, against the fence, always
use the horizontal vise.
The horizontal vise can be installed in two positions on
either the left or right side of the base. When performing
22.5° or greater miter cuts, install the horizontal vise on
the side opposite the direction in which the turn base is
to be turned.
► Fig.45: 1. Vise plate 2. Vise nut 3. Vise knob
By flipping the vise nut counterclockwise, the vise is
released, and rapidly moves in and out. To grip the
workpiece, push the vise knob forward until the vise
plate contacts the workpiece and flip the vise nut clock-
wise. Then turn the vise knob clockwise to secure the
workpiece.
NOTE: The maximum width of workpiece which can
be secured by the horizontal vise is 228 mm.
26 ENGLISH
The workpiece must be secured
Always rotate the vise nut clock-
When cutting a thin workpiece,
Tabla de contenido
loading

Este manual también es adecuado para:

Dls111Dls112

Tabla de contenido