Bench Mounting; Functional Description; Installing Or Removing Battery Cartridge - Makita DLS110 Manual De Instrucciones

Ocultar thumbs Ver también para DLS110:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 130
► Fig.3
1
Switch trigger
5
Switch (for laser line)
(For DLS111, DLS112
only)
9
Wireless activation
button
13
Guide fence (lower
fence)
17
Bevel angle scale
21
45° adjusting bolt (for
bevel angle)
INSTALLATION
Installing the grip
Screw the threaded shaft of the grip into the turn base.
► Fig.4: 1. Grip 2. Turn base
Installing the dust extraction hose
Connect the dust extraction hose to the tool as
illustrated.
Make sure that the elbow and the sleeve fit properly to
the ports of the tool.
► Fig.5: 1. Dust extraction hose 2. Elbow 3. Sleeve
4. Port

Bench mounting

When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. While lowering the
handle slightly, pull the stopper pin and rotate it 90°.
► Fig.6: 1. Locked position 2. Unlocked position
3. Stopper pin
This tool should be bolted with four bolts to a level and
stable surface using the bolt holes provided in the tool's
base. This will help prevent tipping and possible injury.
► Fig.7: 1. Bolt
WARNING:
Ensure that the tool will not move
on the supporting surface. Movement of the miter
saw on the supporting surface while cutting may
result in loss of control and serious personal injury.
2
Lock-off button
6
Battery indicator
10
Wireless activation lamp
14
Guide fence (upper
fence)
18
Releasing lever (for 48°
bevel angle)
-
-
3
Hole for padlock
7
Mode indicator
11
Hose (for dust
extraction)
15
Dust bag
19
Latch lever (for bevel
angle)
-
-
FUNCTIONAL
DESCRIPTION
WARNING:
switched off and the battery cartridge is removed
before adjusting or checking the functions on
the tool. Failure to switch off and remove the battery
cartridge may result in serious personal injury from
accidental start-up.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
► Fig.8: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: The tool does not work with only one battery
cartridge.
21 ENGLISH
4
Lid (for wireless unit)
(For DLS111 only)
8
Check button
12
Stopper pin (for carriage
elevation)
16
0° adjusting bolt (for
bevel angle)
20
Pointer (for bevel angle)
-
Always be sure that the tool is
-
Tabla de contenido
loading

Este manual también es adecuado para:

Dls111Dls112

Tabla de contenido