Know Your Product; Operation; Prior To Initial Operation - SPARKY Professional MBG 150 Instrucciones De Uso

tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
WARNING: The use of any accessories
or attachments differing from the recommended
herewith may present a risk of injury for the operator.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Knob
2. Eye shield 3. Eye shield support
4. Grinding wheel
5. Tool rest
6. ON/OFF switch
7. Base
8. Wheel guard
9. Adjusting nut
10. Dust extraction port
11. Wire wheel brush (MBGT 150)
12. Brush guard (MBGT 150)
13. Tool rest adjusting lever (MBGS 200)
14. Sanding belt tension lever (MBGS 200)
15. Tracking adjustment knob (MBGS 200)
16. Sanding belt housing (MBGS 200)
17. Sanding belt (MBGS 200)
18. Tool rest
19. Screw (MBGS 200)

Operation

This power tool is supplied from single-phase alternating
current mains only. This power tool is Class I according
to EN 61029 -1 and must not be fitted to sockets with-
out protective earthing. This power tool is radio sup-
pressed in compliance with EMC Directive 2004/108/
EC and with EN 55014-1, EN 55014-2, EN 61000-3- 2,
EN 61000- 3-3.
The bench grinder is designed for grinding, sharpening and
finishing operations: sharpening of all kind of tools, cleaning
Original instructions
metal surfaces and metal sections by means of corundum
grinding wheels, wire wheel brush or sanding belt.

PRIOR TO INITIAL OPERATION

WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or mainte-
nance, including accessory replacement.
▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the tool.
▪ Connect the power tool to a socket with protective
earth contact only.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position. If the
plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
▪ If the supply cord is damaged it must be replaced with
a special cord or assembly available from the manu-
facturer or its service agent to avoid a safety hazard.
▪ At low temperatures or when the machine has not
been used for a long time, let the machine operate at
no load for a while.
▪ Place the bench grinder firmly on a flat work bench.
The power tool can be fastened to a work bench
(Fig.1) or special stand SBG 80 (delivered separately)
by M10 bolts. The bench grinder stand SBG 80 can
be fastened to the floor by means of two M12 bolts
(Fig.2).
ASSEMBLY
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or mainte-
nance.
▪ Inspect visually the grinding wheels (4) for mechanical
damages.
▪ Check all fasteners. Ensure that the screws fixing the
wheel guards are securely tightened.
▪ Install the tool rests (5) and adjust their position. The
distance between the tool rest (5) and the wheel (4)
must no exceed 1.6 mm. Tighten the adjusting nuts
(9).
▪ Mount the eye shield supports (3). During normal
operation the operator must have a clear view of the
grinding wheels (4) through the eye shields (2).
WARNING: Never operate the bench grinder
without the wheel guards and the eye shields.
▪ After assembling the machine connect the dust port
(10) to a dust extraction system.
5
EN