Approved Abrasive Tools; Rotating The Machine Head (Gwx 18V-15 C); Dust/Chip Extraction - Bosch GWX 18V-15 C Professional Manual Original

26 | English
Removing the abrasive tool
➊ Open the lever (3).
➋ The grinding/cutting/flap disc will be released.
➌ The grinding/cutting/flap disc can be removed.
(3)
Cup brushes/disc brushes and fibre discs
Always fit the hand guard (16) when working with the
u
cup brush/disc brush or fibre disc.
See the graphics page for fitting instructions.
To remove an application tool, open the lever (3) and re-
move the application tool.

Approved abrasive tools

You can use all the abrasive tools mentioned in these operat-
ing instructions.
-1
The permissible speed [min ] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
max. [mm]
D b
125 7
125 –
75 30
82 –

Rotating the machine head (GWX 18V-15 C)

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
1 609 92A 5RL | (19.06.2020)
(3)
[mm]
-1
d [min ] [m/s]
– 11,000 80
– 11,000 80
– 11,000 45
– 11,000 80
chine head carefully, without removing it from the hous-
ing, into the new position. Screw in and retighten the four
screws.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Start-up
Inserting the battery
Push the charged battery (7) into the base of the power tool
from the front until the battery is securely locked.
Switching on/off
To start the power tool, push the on/off switch (5) forward.
To lock the on/off switch (5) in position, push the on/off
switch (5) forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (5);
or, if the switch is locked, briefly push the on/off switch (5)
backward and down and then release it.
Always check abrasive tools before using them. The
u
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Kickback stop
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically. The kickback stop indicator(25)
The machine head can be
rotated in 90° increments.
In this way, the on/off
switch can be brought into
a more favourable handling
position for particular ap-
plications, e.g. for left-
handed tool users.
Completely unscrew the
four screws. Rotate the ma-
Bosch Power Tools