Electrical Safety; Replacing The Power Cable; Description And Package Contents; The-Package-Contains - IKRA EVL 1500 Instrucciones De Manejo

prescribed-for-the-respective-type-of-tool.--You-should-
also-consider-the-working-conditions-and-the-work-to-
be-carried-out.
•- Have- the- power- tool- serviced- by- qualified- technical-
personnel- only;- repairs- should- be- carried- out- using-
exclusively-original-spare-parts.
•- Replace-worn-or-damaged-parts-for-reasons-of-safety.-
Use-only-original-spare-parts.-Parts-not-produced-by-
the- original- manufacturer- may- have- a- poor- fit- and-
possibly-cause-injury.
•- Grip-guide-bar-firmly-with-both-hands.-Never-operate-
the-tool-with-only-one-hand.
•- Hold- the- guide- bar- and- lift- the- tool- to- move- it- from-
one-place-to-another.-Always-switch-off-the-tool,-dis-
connect-the-plug-and-wait-until-the-application-stops-
before-carrying-out-maintenance.

Electrical safety

•- The- electric- motor- has- been- designed- to- use- single-
phase-voltage-only.
•- Make-sure-your-voltage-corresponds-to-the-one-writ-
ten-on-the-rating-label.
Your machine has double insulation in
conformity to Directive EN 60335, you do
not therefore need to earth.
•- Always- use- a- plug- compulsory- for- double- insulation-
electric-tooling-when-replacing-the-cable.
•- Always-switch-your-machine-off-before-disconnecting-
any-plug,-socket-or-extension.
•- Increased-safety-can-be-obtained-by-having-a-quali-
fied-electrician-install-a-high-sensitivity-(30mA)-circuit-
breaker-in-the-house-wiring.-If-you-do-not-have-such-
a-circuit-breaker-installed,-or-you-do-not-wish-to-have-
one- installed,- then- we- strongly- recommend- that- the-
electrical-power-to-your-Machine-be-supplied-through-
a- high- sensitivity- (30mA)- residual- current- device-
(RCD).-The-RCD-is-designed-to-provide-a-high-degree-
of-personal-protection-against-harmful-electric-current-
should-fault-conditions-occur.
The use of an RCD or other circuit breaker
unit does not release the operator of your
Machine from the safety instructions
and safe working practices given in this
manual.
•- When-using-an-extension,-make-sure-that-it-has-been-
certified- and- is- the- right- size- for- conveying- electric-
ity-supply-to-the-equipment-(see-technical-specifica-
tions).
•- Smallest-size-of-lead-is-1.5-mm².-Completely-unwind-
the-cable-if-you-are-using-a-winder.

Replacing the power cable

If- the- power- cable- of- the- device- should- be- damaged- it-
must-be-replaced-by-the-manufacturer-or-their-after-sales-
service-or-an-equally-qualified-person-to-avoid-any-risks.

5. DESCRIPTION AND PACKAGE CONTENTS

The package contains-(Fig.-1):
•- 1- Machine- body- fitted- with:- lever- to- adjust- height- of-
wheels-(1),-safety-cover-(2)-and-blade-system-of-scari-
fier(3)
•- 1-upper-handle-bar(4)-fitted-with:-switch-with-cable-and-
switch-release-button-(5),-switch-lever-(6)-and-socket-
to-connect-extension-(7)
•- 1-middle-handle-bar(8)
•- 2-lower-handle-bars-(9)-fitted-with:-plastic-holder-(10)
and-knobbed-bolt(11)
•- 2-cable-clamps-(12)
•- 2-sets-of-winged-nut-and-bolts-(13)-to-fix-middle-handle-
bar-to-lower-handle-bar
•- 2-sets-of-knob-nut-and-bolts(14)-to-fix-upper-handle-bar-
to-middle-handle-bar
•- 1-hook-to-hold-extension-(15)
•- 1-set-of-grass-bag(16)
•- 1-set-of-blade-system-of-lawn-raker(17)
•- 1- hexagon- socket- wrench- (18)- to- change- the- blade-
system
NOTE: make- sure- that- the- Machine- and- accessories- in-
the-package-are-not-damaged

6. ASSEMBLY AND SETTING UP

Always disconnect plug from mains before
assembly and setting up
HANDLE ASSEMBLY-(Fig.-2)-
•- Insert- the- knobbed- bolt- of- lower- handle- bar- (9)- from-
outside- in- the- two- holes- in- the- machine- body- and-
screw-the-knobbed-bolt-to-fix-it-(Fig.-2.1).
•- Join-the-middle-handle-bar-(8)-to-the-lower-handle-bar-
(9)- by- means- of- the- winged- nuts- and- bolts- (13)- pro-
vided-(Fig.-2.2).
•- Fit-the-cable-hook-(15)-onto-the-upper-handle-bar-from-
the-switch-side-(Fig.-2.3).
•- Join-the-upper-handle-bar-(4)-to-the-middle-handle-bar-
(8)-by-means-of-the-knobbed-nuts-and-bolts-(14)-pro-
vided-(-Fig.-2.4).
•- Fix- the- cable- to- the- handle- by- the- clamps- (12)- (Fig.-
2.5).
GRASS BAG ASSEMBLY (Fig.-3)-
•- Insert-the-front-metal-frame-into-the-rear-metal-frame-
(Fig.-3.1).
•- Fix- the- front- metal- frame- inside- the- clamping- rims- of-
cloth-bag-(Fig.-3.2).
•- Mount-the-grass-collector-bag-as-shown-in-the-picture-
(Fig.-3.3).
HEIGHT ADJUSTMENT-(Fig.-4)-
•- Use- the- adjustment- arm- (1)- of- the- machine- body- for-
GB-6