Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ENGLISH
WARNING! During the autoset phase, the obstacle detection function is
not active, therefore the installer must control the automation movement
and prevent persons and things from approaching or standing within the
automation working range.
In the case where buffer batteries are used, autosetting must be carried out
with the control panel supplied by mains power voltage.
WARNING: the torque values determined by autosetting refer to
the slow-down speed determined by autosetting.When modifying
the slow-down speed, the slow-down torque values must be modified
as well so that activation of the safety device takes place according
to the new speed set.
WARNING: Check that the impact force value measured at the
points established by the EN 12445 standard is lower than that
specified in the EN 12453 standard.
Incorrect sensitivity setting can cause injuries to persons or
animals, or damage to things.
16) SERIAL CONNECTION USING SCS1 BOARD (Fig.20).
The QSC-D control panel allows several automation units to be connected in
a centralised way by means of appropriate serial inputs and outputs (SCS1
board).This makes it possible to use one single command to open and close
all the automation units connected.
Following the diagram in Fig. 20, proceed to connecting all the QSC-D
control panels, exclusively using a telephone-type line.
Should a telephone cable with more than one pair be needed, it is indispen-
sable to use wires from the same pair.
The length of the telephone cable between one appliance and the next must
not exceed 250 m.
At this point, each of the QSC-D control panels must be appropriately con-
figured, by setting a MASTER unit first of all, which will have control over all
the others, to be necessarily set as SLAVE (see logic menu).
Also set the Zone number (see parameter menu) between 0 and 127.
The zone number allows you to create groups of automation units,
each one answering to the Zone Master unit. Each zone can only be
assigned one Master unit, the Master unit in zone 0 also controls the Slave
units in the other zones.
Loop closing of the serial connection (indicated by a dotted line in Fig.20)
is only needed if you require to check the no. of the connected devices by
means of UNIPRO.
16.1) Opposite sliding leaves (Fig. 20A)
Serial connection also provides centralized control of two opposite sliding
gates (Fig. 20A).
In this case, the Master M1 control board will perform closing and opening
of Slave M2 control board simultaneously.
In case of opposite sliding leaves, the M1 (master) control board and the
M2 (slave) control board should bear the same area number without other
devices being connected in such area.
If the opening direction of one of the two motors is incorrect, invert the
connection 1 and 2 of the motor as well as the connections 6 and 7 of the
opening and closing limiting devices.
The safety devices (photocells and sensing edges) should be connected
according to the diagram in Fig. 20A.
To connect checked safety devices, make reference to whatever is specified
in previous paragraph 13. Carry out connections on the MASTER control
unit and only bring the cable of terminal 24 to the SLAVE control unit. On
the SLAVE control unit, the TEST PHOT switch must be left on OFF.
Start, Open, Close, push-buttons and the Timer contact should be normally
connected to the M1 (master) control board.
The pedestrian command is to be connected to the M2 panel (slave).
The Stop command provides greater safety and is generated by a double contact
NC push-button connected to both control boards as shown in Fig. 20A.
NOTE: Disable the TCA function from the M2 (slave) panel.
17) STATISTICS
Having connected the UNIPRO programmer to the control unit, enter the
CONTROL UNIT / STATISTICS menu and scroll the screenful showing the
statistical parameters:
-
Board microprocessor software version.
-
Number of cycles carried out. If motors are replaced, count the number
of manoeuvres carried out up to that time.
-
Number of cycles carried out from the latest maintenance operation.
It is automatically set to zero after each self-diagnosis or parameter
writing.
-
Date of latest maintenance operation. To be updated manually from the
appropriate menu "Update maintenance date".
-
Installation description. 16 characters can be entered for installation
identification.
18) MANUAL RELEASE
The manual or emergency release is to be activated when you have to open
the gate by hand, and in any event of failed or incorrect operation of the
automation system. To carry out the emergency manoeuvre, you have to:
20 -
URANO BT Ver. 04
INSTALLATION MANUAL
•
Insert the release knob in its appropriate seat (fig.19) and rotate it clockwise
along its entire travel. This way you set the pinion idling, thus allowing to
gate to be opened by hand.
Warning: Do not push the gate leaf hard, but help it along its
entire stroke.
•
To reset motorised control, rotate the knob anticlockwise along its entire
travel, remove the knob and leave it in a safe place which is known to all
the persons concerned.
In the case where a release knob with personalised key is fitted (fig.18),
proceed as follows:
•
Insert the personalised key in the lock, and rotate the key anti-
clockwise.
•
Grip the release knob and rotate it clockwise (fig.18) until it stops.
•
Push the gate leaf by hand and help it along its entire travel.
•
The key cannot be removed from its lock until the knob is returned to its
initial position (motorised activation).
•
To reset motorised control, rotate the knob anticlockwise along it entire
travel and remove the key.
19) AUTOMATION CHECK
Before allowing the automation to be used normally, carry out the following
procedure very carefully:
•
Check the correct functioning of all safety devices (limit microswitches,
photocells, sensitive edges etc.).
•
Check that the thrust (anti-squash) force of the leaf is within the limits
set by current regulations.
•
Check the manual opening command.
•
Check the opening and closing operations with the control devices in use.
•
Check the standard and customised electronic functioning logic.
20) AUTOMATION OPERATION
Since the automation can be remote-controlled by means of a remote control
device or a start button, and so out of sight, the good working order of all the
safety devices should be checked regularly. In the event of any anomalous
functioning of the safety devices, consult a specialised technician immediately.
Keep children at a safe distance from the automation operation area.
21) CONTROL
The automation is used for the power-operated opening and closing of the
gate. The control can be of a number of types (manual, remote-controlled,
magnetic badge access control, etc.) depending on requirements and the
characteristics of the installation. See the specific instructions for the various
control systems. Users of the automation must be instructed about
its control and operation.
22) MAINTENANCE
Disconnect the power supply when carrying out any maintenance opera-
tions.
•
Clean the lenses of the photocells every so often.
•
Have a qualified person (installer) check correct motor torque setting.
•
In the event of any anomalous functioning which cannot be resolved,
disconnect the power supply and contact a specialised technician (in-
staller). Whilst the automation is out of order, activate the manual release
to allow manual opening and closing.
23) SCRAPPING
The
WARNING! This operation should only be carried out by qualified personnel.
Materials must be disposed of in conformity with the current regulations.
In case of scrapping, the automation devices do not entail any particular risks
or danger. In case of materials to be recycled, these should be sorted out by
type (electrical components, copper, aluminium, plastic etc.).
24) DISMANTLING
WARNING! This operation should only be carried out by qualified personnel.
When the automation system is disassembled to be reassembled on another
site, proceed as follows:
•
Disconnect the power supply and the entire external electrical installation.
•
In the case where some of the components cannot be removed or are
damaged, they must be replaced.
WARNINGS
Correct controller operation is only ensured when the data contained
in the present manual are observed. The company is not to be held
responsible for any damage resulting from failure to observe the
installation standards and the instructions contained in the present
manual.
Tabla de contenido
