Explanation Of General View - Makita DLS713 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Stopper pin
2 Bolt
3 Adjusting bolt
4 Red part
5 Button
6 Battery cartridge
7 Star marking
8 Blade guard
9 Blade guard A
10 Blade guard B
11 Thumb screw
12 Kerf board
13 Saw blade
14 Blade teeth
15 Left bevel cut
16 Straight cut
17 Guide fence
18 Turn base
19 Top surface of turn table
20 Periphery of blade
21 Adjusting screw
22 Stopper arm
23 Sub-fence
24 Pointer
25 Miter scale
26 Lock lever
27 Grip
SPECIFICATIONS
Model
Blade diameter ................................................................................................................................................... 190 mm
Blade body thickness ........................................................................................................................... 1.3 mm – 2.0 mm
Hole (arbor) diameter ............................................................................................................................................ 20 mm
Max. Miter angle .................................................................................................................................. Left 47°, Right 57°
Max. Bevel angle ................................................................................................................................... Left 45°, Right 5°
Max. Cutting capacities (H x W) with blade 190 mm in diameter.
Miter angle
0°
45° (left and right)
57° (right)
–1
No load speed (min ) ............................................................................................................................................ 2,200
Dimensions (L x W x H) .....................................................................................................655 mm x 430 mm x 454 mm
Net weight ............................................................................................................................................................ 12.7 kg
Rated voltage .................................................................................................................................................... D.C. 18 V
(Note)
* mark indicates that a wood facing with the following thickness is used.
1: When using a wood facing 20 mm thickness.
2: When using a wood facing 15 mm thickness.
3: When using a wood facing 10 mm thickness.
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Explanation of general view

28 Lever
29 Release button
30 Bevel scale
31 Arm
32 Screw
33 Switch trigger
34 Lock-off button
35 Hole for padlock
36 Wrench holder
37 Hex wrench
38 Center cover
39 Hex wrench
40 Hex socket bolt
41 Safety cover
42 Shaft lock
43 Arrow
44 Blade case
45 Hex socket bolt (left-handed)
46 Outer flange
47 Inner flange
48 Spindle
49 Dust bag
50 Dust nozzle
51 Fastener
52 Support
53 Vise arm
54 Vise rod
45° (left)
25 mm x 300 mm
—
25 mm x 212 mm
—
—
—
55 Holder
56 Holder assembly
57 Vise knob
58 Projection
59 Vise shaft
60 Base
61 Rod 12
62 Clamp screw
63 52/38° type crown molding
64 45° type crown molding
65 45° type cove molding
66 Inside corner
67 Outside corner
68 Over 15 mm (5/8")
69 Over 420 mm (16-1/2")
70 Holes
71 Set plate
72 Cut grooves with blade
73 Triangular rule
74 Arm holder
75 0° bevel angle adjusting bolt
76 Left 45° bevel angle adjusting
77 Limit mark
78 Brush holder cap
79 Screwdriver
Bevel angle
0°
52 mm x 300 mm
*60 mm x 265 mm (Note 1)
52 mm x 212 mm
*60 mm x 185 mm (Note 2)
52 mm x 163 mm
*60 mm x 145 mm (Note 3)
bolt
5° (right)
40 mm x 300 mm
—
—
—
—
—
DLS713
13