Idiomas disponibles
Idiomas disponibles
Ordering replacement parts
Please quote the following data when ordering
replacement parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always use
the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.5
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.5
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain 3/8.05X39DL
Guide rail AL 10-39-507P
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade
11. Storage
Cleaning
• Keep handles free of oil, so you always have a secure hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time before
carrying out any cleaning.
• Never immerse the equipment in water or other liquids
in order to clean it.
• Store the petrol multi garden tool in a safe and dry
place out of the reach of children.
Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the following
steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can cau-
se problems when starting up the equipment and may
require expensive repairs.
1 Slowly remove the fuel tank cap to release any pres-
sure that may have formed in the tank. Carefully em-
pty the tank. Only ever empty the tank outdoors or in
well-ventilated rooms.
chain oil into the soil (environmental protection).
Use a proper base.
2 To remove the fuel from the carburetor, start the engine
and let it run until the equipment stops.
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change and
clean the spark plug).
5 Add one teaspoon of 2-stroke engine oil into the com-
bustion chamber. Slowly pull the starter cord several
times to apply a layer of oil to all internal components.
7910700706
Fit the spark plug again.
7910700702
Note: Store the equipment in a dry place and far away
3904801065
from possible ignition sources such as an oven, a gas-fi
7910700705
red hot water boiler, a gas-fi red dryer, etc.
3904801066
7910700711
Putting the equipment back into operation
3904801066
3904803034
1 Remove the spark plug (see section 10 Change and
clean the spark plug).
7910700716
2 Quickly tug on the starter cord to remove excess oil
7910700717
from the combustion chamber.
7910700704
3 Clean the spark plug and check that the electrode gap
3904801037
is correct, or insert a new spark plug with the correct
3904801039
electrode gap.
7910700710
4 Prepare the equipment for operation.
Transport
7910700703
To transport the machine, empty the petrol tank as
3904801043
described in section 8 draining fuel. Clean coarse dirt off
the equipment with a brush or hand brush.
12. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types of
material, such as metal and plastic. Defective compo-
nents must be disposed of as special waste. Ask your
dealer or your local council.
Make sure not to spill fuel or
GB
41
