Comet CRRL 75 Manual De Instrucciones página 37

• Keep the power lead, any extensions, the plugs and the sockets dry. Do not touch with wet hands.
• If the power lead is damaged, contact a
• Keep clear of moving parts of the machine, even if these are adequately protected.
• Do not remove the guards of the moving parts.
• Do not touch pipes containing liquids under pressure.
• Do not perform maintenance operations on the machine if this is operating.
• Read the
"INTENDED USE"
• Do not modify in any way the installation conditions of the machine. In particular, do not modify the
fastening, the hydraulic connections and the guards.
• Do not operate any taps on the machine unless these are connected to an accessory that prevents the
accidental escape of the pumped liquid.
• Do not deactivate or tamper with the controls and the safety devices and the pressure unloader/regulation
valve.
a) Unroll the delivery hose (1) completely.
b) Check that the lance (13) adjuster (24) is turned completely in the
into the position. If provided, move the tap lever (39) into the
"OFF"
c) Reset delivery pressure as follows:
- motor pumps with MC 8 and MC 18: turn knob (29) completely anticlockwise;
- other motor pumps: put lever (30) into the
d) S tart the machine for priming to start. If the machine has an electric motor, turn the main switch on, putting
it into position "1" (bear in mind the warning concerning three-phase motors given in the
AND CONNECTINg UP TO THE POwER SUPPLY"
follow the instructions for starting given in the engine manual.
e) Pressurise the machine in the following way:
- when installed, put lever (30) into the
- turn knob (29) until the pressure value wanted is reached (turning clockwise to increase pressure,
anticlockwise to reduce it); if installed, the pressure is shown on the pressure gauge (36).
f) If provided, move the tap lever (39) into the
g) Turn the lance (13) lever (26) to adjust the spraying angle (from an empty cone to a thin solid jet). The
position of the spray chosen can be fixed with the adjuster (24). We advise doing this spraying the lance
inside the tank so as not to disperse the chemical product.
h) The flow of liquid sprayed depends on working pressure, on the nozzle (27) used (the machine comes
with a standard 1.5 mm Ø nozzle) and on the spraying angle set. The nozzle to use for the type of job to
be done can be found in the following table (note that the flow rate given is the maximum, that is, for a
thin and solid jet).
Ø NOZZLE
[mm]
1,0
1,0 - 0,26
1,2 1,4 - 0,37
1,5
2,0 - 0,53
1,8
2,2 - 0,58
2,0
2,6 - 0,69
CAUTION
• To permit fast machine priming, proceed as indicated at point c) every time the tank is emptied of fluid.
• During the first hours of operation, it is best to check the oil level and, if necessary, top up the level,
following the instructions in the
• Do not operate the machine:
- if it is too noisy and/or water or oil is dripping from it: in this case have it checked by a
- when exposed directly to sunlight, with ambient temperature above 40 °C.
SkILLED TEChNICIAN
paragraph carefully.
"PRESS"
5 - 72,5 10 - 145
1,5 - 0,40
1,9 - 0,50
2,8 - 0,74
3,2 - 0,85
3,7 - 0,98
"PRELIMINARY ACTIVITIES"
to have it replaced.
"S"
position.
"BYPASS"
paragraph). In machines fitted with a combustion engine,
position;
position.
"ON"
[bar - psi]
PRESSURE
15 - 217,5 20 - 290
1,8 - 0,48 2,1 - 0,55
2,4 - 0,63 2,8 - 0,74
3,4 - 0,90 3,9 - 1,03
3,9 - 1,03 4,5 - 1,19
4,5 - 1,19 5,2 - 1,37
[l/min - USgpm]
FLOW RATE
paragraph.
direction so lever (26) can be moved
position.
"OFF"
30 - 435 40 - 580
2,5 - 0,66 2,9 - 0,77
3,4 - 0,90 3,9 - 1,03
4,8 - 1,27 5,6 - 1,48
5,5 - 1,45 6,3 - 1,66
6,4 - 1,69 7,4 - 1,95
SkILLED TEChNICIAN
EN
"CHECkINg
;
37