Idiomas disponibles
Idiomas disponibles
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Damage to hearing if no suitable ear protec-
tion is used.
2. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
5.1 Assembling the components
Some parts of the equipment come disassem-
bled. For quick and easy assembly, read and
follow the instructions below.
Note! You will need the following additional tools
(not supplied) for assembly, and also for mainte-
nance work:
•
One flat oil drip tray (for changing the oil)
•
One 1 liter measuring jug (oil/petrol resistant)
•
One petrol can
•
One funnel (suitable for the tank's petrol filler
neck)
•
Household wipes (to wipe up oil/petrol resi-
due; dispose of these at a filling station)
•
One petrol suction pump (plastic, available
from DIY stores)
•
One oil can with hand pump (available from
DIY stores)
•
Engine oil
Assembly
1. Fit the lower and upper push bar (Item 3) as
shown in Fig. 3a-3b. Choose one of the three
positions to suit the required height of the
handle and engage the quick-release faste-
ner (Item 12). Important! The identical height
Anl_GTR_E_51_R_HW_SPK7.indb 22
Anl_GTR_E_51_R_HW_SPK7.indb 22
GB
must be set on both sides.
2. Insert the grip of the starter cable (Item 9) into
the hook provided for that purpose as shown
in Fig. 3c.
3. Fasten the actuator cables to the push bar
with the supplied cable clips (Item 10) as
shown in Fig. 3d.
4. The wheel mount (Item 15) is mounted on
the bar (Item 20) with the screw (Item 15) as
shown in Fig. 3e.
5. The bar is mounted with four screws (17) on
the mower housing (Fig. 3f).
6. Lift the ejector fl ap (Item 5a) with one hand
and hook in the grass bag (Item 4a) as shown
in Fig. 4a.
5.2 Adjusting the cutting height
Warning! Adjust the cutting height only when the
engine has been switched off .
Rear wheel
The cutting height is centrally adjusted for the rear
wheels with the cutting height adjustment lever
(Fig. 7a/Item 8).
Actuate the adjustment lever and pull it to the re-
quired position. Let the lever latch into position.
Front wheel
The front wheel must be moved to the same level
as the rear wheels by moving the axle (Fig. 7b/
Item 8).
6. Operation
Note!
The engine comes without oil and petrol.
Therefore, be sure to add oil and petrol befo-
re starting the engine.
1. Check the oil level (see 7.2.1).
2. Use a funnel and measuring jug to fi ll the tank
with petrol. Make sure that the petrol is clean.
Warning: Never use more than one safety petrol
can. Do not smoke when refueling. Switch off the
engine before refueling and allow the engine to
cool down for a few minutes.
3. Ensure that the ignition cable is connected to
the spark plug.
- 22 -
25.10.2016 12:46:48
25.10.2016 12:46:48
