Idiomas disponibles
Idiomas disponibles
2. Push the "ON/OFF" switch to position "ON" (Fig. J2).
3. Pull the kickback brake paddle towards the main
handle to the
position.
4. Move the locking tongue (J-3) forwards and then
press the variable-speed trigger (J-4). The more
you pull up the variable-speed trigger, the higher
rotating speed the saw chain is (Fig. J3).
J-1 Electric Socket
J-3 Locking Tongue
J-2 Power Plug
J-4 Variable-speed Trigger
To Stop
1. Release the variable-speed trigger to stop the chain saw.
NOTICE:
The saw chain will continue to rotate for a short
while after the variable-speed trigger is released. Take care
to avoid contact after releasing the variable-speed trigger
and when setting down the chain saw.
2. Push the kickback brake paddle forward to the brake
position "
".
3. Turn the "ON-OFF" switch to position "OFF".
WARNING:
Always disconnect the power plug from
the chain saw during work breaks and after finishing work.
PREPARATION FOR CUTTING
Proper Grip On Handles (Fig. K)
◾
Wear non-slip gloves for maximum grip and protection.
◾
Always grasp the front handle with the left hand and
the main handle with the right hand.
◾
The fingers should encircle the handle, with the thumb
wrapped under the front handle.
WARNING:
Never use a left-handed (cross-handed)
grip, or any stance which would place your body or arm
across the chain line.
WARNING:
Do not operate the trigger switch with
your left hand and hold the front handle with your right
hand. Never allow any part of your body to be in the chain
line while operating a chain saw (Fig. L).
CHECKING CHAIN LUBRICATION (Fig. M)
NOTICE:
Ensure oil tank of the chain saw have been filled
with proper volume of chain oil.
1. Hold the guide bar above a light colored surface.
2. Switch on the saw. You will see a clear line of oil
on the light colored surface after 1 minute, if Chain
lubrication is operating properly.
56 VOLT LITHIUM-ION CORDLESS TOP HANDLE CHAIN SAW — CSX3000
3. If chain oil is still not visible on the light colored
surface, Refer to the section "ADJUSTING OIL-
FLOW" to adjust it
OPERATING IN THE TREE
WARNING:
When working or climbing, it is recommend
to use the additional support , such as foot stirrup, adjustable
lanyard to prevent a swing or a cutting accident.
Brefore using it , please check following points:
◾
Check the wear marks on the chain sprocket (N-1), If
wear marks are deeper than 0.5 mm: contact your EGO
servicing dealerto replace the chain sprocket.
◾
Also check the braking system , if wear marks on
the brake lining (N-2) are uneven, contact your EGO
servicing dealer to replace the brake lining must be
replaced (Fig. N).
N-1 Chain Sprocket
◾
Check the guide bar see related section:
GUIDE BAR MAINTENANCE
◾
Check the saw chain see related section:
CHAIN MAINTENANCE
◾
Testing the chain brake see related section:
KICKBACK SAFETY DEVICES ON THIS
CHAIN SAW
◾
Check the controls see related section:
STARTING/STOPPING THE CHAIN SAW
◾
Check the chain lubrication see related section:
CHECKING CHAIN LUBRICATION
MAINTENANCE
CLEANING
◾
After each use, clean debris from the chain and guide
bar with a soft brush. Wipe the chain saw surface with
a clean cloth moistened with a mild soap solution.
◾
For deep clearing, remove the side cover assembly, take
down the guide bar and saw chain and then use a soft
brush to thoroughly remove debris from the guide bar, saw
chain, and the drive sprocket on the chain saw power head.
◾
Always clean out wood chips, saw dust, and dirt from
the guide bar groove when replacing the saw chain.
REMOVE DUST
1. Disconnect the power plug, allow the chain saw to
cool and tighten the oil-tank cap.
2. Engage the saw brake
N-2 Brake Lining
11
EN
