Idiomas disponibles
Idiomas disponibles
FILLING OILTANK
EN
1. Disconnect the battery pack from the chain saw.
2. Position the chain saw on its side on a firm, flat surface,
so that the oil-tank cap is facing upwards. Open the
oil-tank cap. if it is too tight, use the slot-head of the
combi- wrench (provided) to loosen it (Fig. E).
3. Carefully pour the oil into the oil tank. Fill to the bottom
of the fill neck. Wipe off any excess oil and close it.
NOTICE:
◾
The chain saw is not filled with oil at the time of
purchase. It is essential to fill the tank with oil before
use. The chain is automatically lubricated with chain oil
during operation.
◾
It is specially designed to provide low friction and
faster cuts.
◾
Never use oil or other lubricants not specifically
designed for use on the bar and chain. This can lead
to a clogged oil system, which may cause premature
wear of the bar and chain.
ADJUSTING OIL-FLOW (Fig. F)
◾
This saw is equipped with an Oil-Flow Adjustment
Screw (F-1), located on the bottom of the tool, it is
used to adjust the oil flow for lubricating the chain, bar
and cutting system. Increasing or reducing the oil-flow
in the direction of arrows as marked on the housing.
LED INDICATOR ON THE CHAIN SAW
The chain saw is equipped with 2 LED indicators to indicate
oil status and the charge level of the battery pack(s).
LED indicator
Low oil-
Flashing red Oil shortage
indicator
(A-8)
Off
Shining
green
Battery
indicator
Flashing
(A-7)
green
ATTACHING THE BATTERY HOLSTER TO THE CLIMBING
HARNESS
This chainsaw comes with a battery holster, it is used to
carry the battery pack and allows to be attached to the
climbing harness (not provided).
10
56 VOLT LITHIUM-ION CORDLESS TOP HANDLE CHAIN SAW — CSX3000
Meaning
Action
Fill the oil
tank
Has the oil
/
Battery pack has
/
the power
Battery pack is
nearly depleted
Charge the
and needs to
battery
be charged
immediately.
NOTICE:
Fastening the battery holster firmly onto the
climbing harness, prior to wear the climbing harness.
WARNING:
The climbing harness with quick-release
function need to be prepared to prevent the emergency
occurs.
1. Seek a preferable point for hanging this battery
holster on the climbing harness, hang the battery
holster on the climbing harness by using the belt
hook (G-1) (Fig. G1).
2. Wrap the belt around the climbing harness to fix
battery holster in place (Fig. G2 & G3).
3. Attach two rings (G-2) of safety strop to the climbing
harness by using two karabiners (not provided), as
shown in Fig G4.
G-1 Belt Hook
G-2 Rings
NOTICE:
◾
When climbing the tree, attaching the ring 1 & 2 of
the safety strop to the climbing harness by using
karabiners(not provided) (Fig. G5).
◾
When the tool is in use, detach the ring 2 from the
climbing harness, hold the saw by two hands to
perform your cutting (Fig. G6).
SECURING THE SAW TO BATTERY HOLSTER
Attach the saw hook (H-2) of safety strop to the eyelet
(H-1) (Fig. H).
H-1 Eyelet
H-2 Saw Hook
INSTALLING/REMOVING BATTERY PACK
NOTICE:
Fully charge the battery pack before its first use.
To Install (Fig. I1)
Align the ribs of the battery pack with the mounting slots
then slide the battery pack into the battery holster until it
snaps into position.
To Remove (Fig. I2)
Press the battery release button with your thumb to remove
the battery pack.
STARTING/STOPPING THE CHAIN SAW
To Start
" marks on the power plug(J-2) and
1. Align the "
the chain saw 's electric socket(J-1), then insert the
plug into the chain saw until the GREEN seal on the
plug COMPLETELY disappears into the socket (Fig.J1).
