Makita UM600D Manual De Instrucciones página 18

CAUTION:
Never use the tool without install-
ing the undercover.
10. Remove the blade cover, and then turn on the tool
to check that it works properly.
NOTICE:
If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing the shear
blades for hedge trimmer
CAUTION:
Attach the blade cover before
removing or installing the shear blades.
NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
Removing the shear blades
1. Place the tool upside down.
► Fig.23
2. While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.24
3.
Remove the undercover.
► Fig.25
4. Loosen the two screws with a screwdriver and
remove the shear blades.
► Fig.26: 1. Screws
NOTE: The shear blades can be removed without
removing the screws.
5. Remove the crank from the shear blades.
► Fig.27: 1. Crank
NOTE: The crank may remain in the tool.
Attach the blade cover and the storage case to the
removed shear blades, and then store the blades.
Installing hedge trimmer blades
1. Prepare the crank, undercover, and new hedge
trimmer blades.
► Fig.28: 1. Crank 2. Undercover 3. Hedge trimmer
blades
2. Attach the blade cover to the hedge trimmer
blades.
► Fig.29
3. Adjust the three pins so that they are lined up on
the alignment line.
► Fig.30: 1. Alignment line
4. Apply a small amount of grease to the periphery
of the crank. Attach the crank to the pins with the small
and large rounds facing down.
► Fig.31: 1. Crank
on the undercover is aligned
5. Slide the shear blades so that the hole on the
base plate is positioned at the center of the rings of the
blades.
► Fig.32
6. Turn the shear blades upside down and install
them so that the pin on the tool fits in the hole on the
shear blades. Insert the claw of the base plate into the
groove on the tool. Make sure that the shear blades are
fixed securely in place.
► Fig.33: 1. Claw
7.
Tighten the two screws firmly with a screwdriver.
► Fig.34: 1. Screws
8. Place the undercover so that
cover is aligned with
► Fig.35
9. While pressing the undercover, turn it clockwise
until on the undercover is aligned with
lever.
► Fig.36
10. Make sure that the lock lever fits in the groove on
the undercover.
► Fig.37: 1. Lock lever
CAUTION:
Never use the tool without install-
ing the undercover.
11. Remove the blade cover, and then turn on the tool
to check that it works properly.
NOTICE:
If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing the chip
receiver
Optional accessory
CAUTION:
When installing or removing the
chip receiver, always wear gloves and attach the
blade cover so that your hands and face do not
directly contact the blade.
The chip receiver gathers discarded leaves and makes
clean-up afterward much easier. It can be installed on
either side of the tool.
To install the chip receiver, press it against the shear
blades so that the hooks fit into the holes of the shear
blades.
► Fig.38: 1. Hooks 2. Holes
To remove the chip receiver, press the levers on both
sides to release the hooks.
► Fig.39: 1. Levers
NOTICE:
Never try to remove the chip receiver
by an excessive force with its hooks locked in the
holes of the blades.
18 ENGLISH
on the under-
on the lock lever.
on the lock