Mitsubishi Electric PUZ-HA.NHA2 Serie Manual De Instalación página 10

8. Special Functions
®
® ® ®
' (( _ B.... I(bl _il_lC) I
I " \\ ' Orangel2] ,_1_@:)1
I Fig. 8-1
L_ _ _z:______, L........ • CNL_2_
®
@ Circuit diagram example (low noise mode) @ Outdoor unit control board
® On-site arrangement ® Max. 10 m, 33 ff
© External input adapter (PAC-SC36NA)
8.1. Low noise mode (on-site modification) (Fig. 8-1)
By performing the following modification, operation noise of the outdoor unit can be
reduced by about 3-4 dB.
The low noise mode will be activated when a commercially available timer or the
contact input of an ON/OFF switch is added to the CNDM connector (option) on the
control board of the outdoor unit.
• The capacity may be insufficient according to the outdoor temperature and condi-
tions, etc.
(_ Complete the circuit as shown when using the external input adapter (PAC-
SC36NA). (Option)
Q SW1 ON: Low noise mode
SWl OFF: Normal operation
®
® ®
i- i / i
i i ' i
, , \! ,
Red[_
®
Fig. 8-2
®
@ Circuit diagram example (Demand function) © External input adapter (PAC-SC36NA)
® On-site arrangement @ Outdoor unit control board
®Max. 10 m, 33 ft
8.2. Demand function (on-site modification) (Fig. 8-2)
By performing the following modification, energy consumption can be reduced to 0
-100% of the normal consumption.
The demand function will be activated when a commercially available timer or the
contact input of an ONtOFF switch is added to the CNDM connector (option) on the
control board of the outdoor unit.
(_ Complete the circuit as shown when using the external input adapter
(PAC-SC36NA). (Option)
Q By setting SW7-1 and SW7-2 on the control board of the outdoor unit, the ener-
gy consumption (compared to the normal consumption) can be limited as shown
below.
SW7-1 SW7-2 Energy consumption (SW2 ON)
OFF OFF 0% (Stop)
ON OFF 50%
OFF ON 75%
8.3. Refrigerant collecting (pump down)
Perform the following procedures to collect the refrigerant when moving the indoor
unit or the outdoor unit.
@} Supply power (circuit breaker).
* When power is supplied, make sure that "CENTRALLY CONTROLLED" is not
displayed on the remote controller. If "CENTRALLY CONTROLLED" is dis-
played, the refrigerant collecting (pump down) cannot be completed normally.
® After the gas stop valve is closed, set the SWP switch on the control board of the
outdoor unit to ON. The compressor (outdoor unit) and ventilators (indoor and
outdoor units) start operating and refrigerant collecting operation begins. LED1
and LED2 on the control board of the outdoor unit are lit.
* Only set the SWP switch (push-button type) to ON if the unit is stopped. How-
ever, even if the unit is stopped and the SWP switch is set to ON less than
three minutes after the compressor stops, the refrigerant collecting operation
cannot be performed. Wait until compressor has been stopped for three min-
utes and then set the SWP switch to ON again.
@ Because the unit automatically stops in about two to three minutes after the
refrigerant collecting operation (LED1 and LED2 are lit), be sure to quickly close
the gas stop valve. When LED1 and LED2 are lit and the outdoor unit is stopped,
open the liquid stop valve completely, and then repeat step 2 after three minutes
have passed.
* If the refrigerant collecting operation has been completed normally (LED1 and
LED2 are lit), the unit will remain stopped until the power supply is turned off.
@ Turn off the power supply (circuit breaker).
9. System control (Fig. 9-1)
®SW1 -3~6 oFFON
3 4 5 6
®SWl -3~6 oFFON
3 4 5 6
@SWl -3~6 oFFON
3 4 5 6
TB1 ___ TB1 [
D1
_)
E3®E3®$
@ Outdoor unit
® Indoor unit
© Master remote controller
Subordinate remote controller
® Standard 1:1 (Refrigerant address = 00)
@ Simultaneous twin (Refrigerant address = 01)
@ Simultaneous twin (Refrigerant address = 02)
Ta51_
J
Fig. 9-1
* Set the refrigerant address using the DIP switch of the outdoor unit.
(_ Wiring from the Remote Control
This wire is connected to TB5 (terminal board for remote controller) of the indoor
unit (non-polar).
Q When a Different Refrigerant System Grouping is Used.
Up to 16 refrigerant systems can be controlled as one group using the slim MA
remote controller.
Note:
In single refrigerant system(twin), there is no need of wiring®.
sw1
Function table
<SWI>
Function
1 Compulsory
defrosting
2 Error history
SWl
clear
function
3 Refrigerant
settings
4 system ad-
5 dress setting
6
Operation according to switch setting
ON OFF
Start Normal
Clear Normal
Settings for outdoor unit addresses
0to 15
10