Idiomas disponibles
Idiomas disponibles
nOTE: If the cylinder of the punch head
bottomed‑out during a cycle, the cycle complete
LED
15
will flash yellow for five seconds and the tool
will turn off. Bottoming out the tool's cylinder may cause
premature leakage of the tool, requiring service.
5. Turn the tool off by pressing the power ON/OFF
button
.
11
6. Push and hold the hydraulic ram return switch
return the puller
5
to its base position.
7. Rotate the puller guard
the tool.
8. Remove the material from the assembly by unscrewing
the punch from the draw stud.
nOTE: The edges of the material may be sharp. Use
gloves when handling the discarded material.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: Before each use, inspect the tool
(including LED indicators) and correct any
problems before attempting to use.
WARNING: Skin injection hazard. The oil in the
mechanism is under extreme pressure. Do not
use hands to check for oil leaks. If oil leakage is
observed, return tool to a D
service center without further use.
WARNING: Explosion hazard. The internal
hydraulic system creates extreme pressures.
Only D
WALT‑qualified personnel should service
e
this tool.
Required Maintenance (Fig. A)
Maintenance is recommended when the knockout tool
reaches 5000 cycles. The maintenance LED
continuously, signifying the recommendation to service the
tool. Take your tool to a DEWALT factory service center for
maintenance and recalibration.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
1
is
3
to remove the draw stud from
6
WALT authorized
e
lights yellow
16
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
to
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Tool Connect™ Chip (Fig. G)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
English
e
WALT. Call 1‑800‑4‑D
WALT
e
e
that hold the Tool
17
19
into the tool.
.
18
WALT
11
