Idiomas disponibles
Idiomas disponibles
7. Slip thecompression
sleeve andcompression
nut o nto the
copper tubing a sshown. Insert the end ofthetubing i ntothe
outlet endsquarely asfarasitwillgo.Screw c ompression
nut
onto outlet end withadjustable wrench. Donotovertighten.
8. Place t hefree end ofthe tubing i nacontainer orsink, and turn
ONthemain water s upply. Flush thetubing u ntil water i sclear.
Turn O FF theshutoff valve onthewater p ipe. C oil t hecopper
tubing.
Style
2
1.
Unplug
refrigerator
or disconnect
power.
2.
Remove
and
discard
the
black
nylon
plug
from
the
gray
water
tube
on the
rear
of the
refrigerator.
3.
Thread
the
provided
nut onto
the
water
valve
as shown.
NOTE:
Tighten
the
nut by
hand.
Then
tighten
it with
a wrench
two
more
turns.
Do not
overtighten.
6.
On models
with ice makers, the ice maker
is equipped
with a
built-in
water
strainer.
If your water
conditions
require a second
water
strainer,
install it in the 1/4" (6.35 mm) water
line at either
tube connection.
Obtain
a water
strainer
from your nearest
appliance
dealer.
Style
2
1.
Unplug
refrigerator
or disconnect
power.
2.
Remove
and
discard
the
black
nylon
plug
from
the gray
water
tube
on the
rear
of the
refrigerator.
3.
If the
gray
water
tube
supplied
with
the
refrigerator
is not
long
enough,
a 1/4" x 1/4" (6.35
mm
x 6.35
mm)
coupling
is needed
in
order
to connect
the
water
tubing
to an existing
household
water
line.
Thread
the
provided
nut onto
the
coupling
on the
end
of the copper
tubing.
NOTE:
Tighten
the
nut by
hand.
Then
tighten
it with
a wrench
two
more
turns.
Do
not overtighten.
A
/ ii
B
,4. Bulb
B. Nut (provided]
4.
Turn shutoff
valve ON.
5.
Check for leaks. Tighten
any nuts or connections
(including
connections
at the valve) that leak.
Connect to Refrigerator
Style 1
1.
Unplug
refrigerator
or disconnect power.
2.
Attach
the copper
tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression
nut. Do not
overtig hten.
3.
Use the tube clamp
on the back of the refrigerator
to secure
the tubing
to the refrigerator
as shown. This will help avoid
damage
to the tubing
when the refrigerator
is pushed
back
against
the wall.
4.
Turn shutoff
valve ON.
5.
Check for leaks. Tighten any connections
(including
connections
at the valve) or nuts that leak.
A
B
--
C
A.
Tube c/amp
D. Compression
nut
B. Tube c/amp
screw
E. Valve
inlet
C. Copper
tubing
A
B
C
D
E
F
G
A. Refrigerator
water
tubing
B. Nut
(provided]
C. Bulb
D. Coupling
(provided]
E Ferrule
(purchased]
F, Nut
(purchased]
G. Household
water
line
4.
Turn shutoff
valve ON.
5.
Check for leaks. Tighten
any nuts or connections
(including
connections
at the valve) that leak.
Complete the Installation
Electrical
Shock Hazard
Plug into a grounded
3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow these instructions can result in death,
fire, or electrical
shock.
1. Plug into a grounded 3 prong outlet.
NOTES:
•
Allow 24 hours to produce
the first batch of ice. Discard
the
first three batches
of ice produced.
Allow 3 days to completely
fill ice container.
•
For models
with a water
dispenser,
flush the water
system. See
"Water
Dispenser."
10
