Idiomas disponibles
Idiomas disponibles
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (35) until the angle between
the blade (7) and the turntable (19) equals
90°.
•
Retighten the lock nut (37) to secure this
setting.
•
Finally, check the position of the pointer (24).
If necessary, release the pointer with a cros-
stip screwdriver, move to the 0° position of the
angle scale (25) and retighten the pointer.
•
The angle stop (a) and crosstip screwdriver
are not included in the scope of this delivery.
5.6 Precision adjustment of the angle stop
for miter cut 45° (Fig. 8, 10)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (36) until the angle between
the blade (7) and the turntable (19) equals
exactly 45°.
•
Retighten the lock nut to secure this setting.
•
No angle stop (b) included.
6. Operation
6.1 Charging the lithium-ion battery pack
(Figs. 11, 12, 19)
1. Remove the rechargeable battery (43) from
the mount (40) by pressing the pushlock
button on the battery and pulling it out of the
mount.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(46) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section "Charger indicator" you will find a table
with an explanation of the LED indicator on the
charger.
Anl_TE-SM_36-8_L_Li_SPK13.indb 27
Anl_TE-SM_36-8_L_Li_SPK13.indb 27
GB
If the battery pack fails to become charged,
please check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the charg-
ing contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fires.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully dis-
charged. This will cause it to develop a defect.
6.2 Battery capacity indicator (Fig. 12)
Press the button for the battery capacity indicator
(c). The battery capacity indicator (d) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED flashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove
the battery from the equipment, keep it at room
temperature for one day. If the fault reoccurs, this
means that the rechargeable battery has under-
gone exhaustive discharge and is defective. Re-
move the battery from the equipment. Never use
or charge a defective battery.
- 27 -
19.10.2023 10:22:26
19.10.2023 10:22:26
