Idiomas disponibles
Idiomas disponibles
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 General information
•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment's moving parts run
smoothly.
5.2 Assembling the saw (Fig. 1-5)
•
Thread the workpiece supports (10) onto the
guides (9) (Fig. 4). Then fit the guides onto
the fixed saw table (18) and fasten them with
the screw (12). Use a crosstip screwdriver to
do this.
•
The workpiece support (10) can be moved on
the guide (9) to adjust it to the length of the
workpiece you want to saw. Once the workpi-
ece support (10) is in the right position, screw
the locking grip (11) downwards so that it is
in contact with the support surface. This is to
prevent the saw tilting when you work on long
or large workpieces.
•
Important! The hex key (45) can be kept at the
back of the machine (see Fig. 2b).
•
To fit the sawdust bag (27) to the discharge
opening (28) on the crosscut saw, spread the
metal ring apart on the opening. When the
metal ring is back in its original shape, the sa-
wdust bag is held securely in position.
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
A crosstip screwdriver is not supplied with
the product.
5.3 Adjusting the saw (Fig. 1-3)
•
To adjust the turntable (19), the locking lever
(20) must be in the top position. Only then is it
possible to adjust the turntable while holding
the release button (21) pressed down. (see
Fig. 5b)
Anl_TE-SM_36-8_L_Li_SPK13.indb 26
Anl_TE-SM_36-8_L_Li_SPK13.indb 26
GB
•
Turn the turntable (19) and scale pointer (22)
to the desired angular setting on the scale
(23).
•
The saw has locking positions at angles of -
45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30° and
45°, at which the turntable (19) audibly clicks
into position. Once the turntable is engaged,
the setting must be additionally secured by
pressing the locking lever (20) down.
•
If different angle settings are required, the
turntable (19) may be secured in position
using only the locking lever (20).
•
To release the saw from its position at the
bottom, pull the retaining pin (30) out of the
motor mounting while pressing down lightly
on the machine head (4).
•
Swing up the machine head (4).
•
When the locking grip (26) is undone, you
can tilt the machine head (4) to the left by up
to 45°. After the desired angular setting has
been set on the scale pointer (24) on the sca-
le (25), secure the machine head (4) again
with the locking grip (26).
•
To ensure that the saw is standing securely,
adjust the adjustable foot (17) by turning it so
that the saw stands in a horizontal and firm
position.
•
The machine head (4) can be moved back-
wards and forwards using the drag function.
To prevent the drag function, the guide rails
can be fixed in a specific position with the
locking screw (29).
5.4 Precision adjustment of the stop rail
(Fig. 6, 7)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (7) and the stop rail (13).
•
Slacken the four adjustment screws (44)
using a hex key, set the stop rail (13) to 90° in
relation to the saw blade (7) and retighten the
adjustment screws (44).
•
The angle stop (a) and hex key (5 mm) are
not included in the scope of this delivery.
5.5 Precision adjustment of the angle stop
for crosscut 90° (Fig. 8, 9)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the right to 0° using
the handle (1).
- 26 -
19.10.2023 10:22:26
19.10.2023 10:22:26
