Declaration Of Conformity; Noise/Vibration Information; After-Sales Service And Application Service - Bosch PST 700 E Manual Original

OBJ_BUCH-1067-004.book Page 11 Wednesday, June 5, 2013 7:03 PM

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 02.05.2013

Noise/Vibration Information

The measured values of the machine are listed in the table on
page 63.
Noise and vibrational values (vector sum of three directions)
determined according to EN 60745.
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or poorly main-
tained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should al-
so take into account the times when the tool is switched off
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep hands warm, organise work patterns.
Mounting and Operation
Action
Inserting the Saw Blade
Removing the Saw Blade
Adapting the position of the guide
roller
Mounting the splinter guard
Mounting and use of "Cut Control" 5
Bosch Power Tools
Action
Connecting the dust extraction
Adjusting the Cutting Angle
Switching on the sawdust blower
device
Switching On and Off
Guide the power tool toward the
workpiece only when switched on 10
Plunge Cutting
Lubrication when cutting metal
Selecting Accessories
Maintenance and Cleaning
 For safe and proper working, always keep the machine
and the ventilation slots as well as the tool holder
clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Check the guide roller regularly. If worn, it must be replaced
through an authorised Bosch after-sales service agent.
Lubricate the guide roller occasionally with a drop of oil (see
figure 14, page 70).
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application
Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
Figure Page
North Orbital Road
1 64
Denham
Uxbridge
2 64
UB 9 5HJ
Tel. Service: (0844) 7360109
3 64
Fax: (0844) 7360146
4 65
E-Mail: [email protected]
65
English | 11
Figure Page
6 66
7 66 –67
8 67
9 68
68
11 69
12 69
– 71 –72
1 609 92A 083 | (5.6.13)