Active 3.5-Z 4T Manual De Instrucciones página 25

WARNING : WARNING :
WARNING : The weight of the machine must be supported WARNING : WARNING :
by the waist-band (A).
Fig.12/1 - To loosen the straps, pull the the handle of the Fig.12/1 Fig.12/1 Fig.12/1 Fig.12/1
buckle upwards.
Have the engine horizontally, unscrew the cap and fill the
tank of oil from the threaded hole..
The capacity of the tank is approximately 0.09L.
It recommends the use of oil type SAE 10W-30 SF or
higher. Use of Multi-grade oil tends to increase
consumption at high temperatures. Do not add oil with
characteristics different from those of already
existing in the engine
When the tank is full, tighten the cap of the oil.
The lubrication of your engine is vital to ensure the perfor-
mance and durability of your car.
It is recommended for both follow the rules prescribed by
the manufacturer in terms of regular maintenance.
WARNING WARNING WARNING Carefully read the safety precautions before WARNING WARNING
using the brushcutter.
Put on the harness. For balancing and adjustment see
ASSEMBLY ASSEMBLY ASSEMBLY ASSEMBLY ASSEMBLY
Always keep both hands on the handles operating the
brushcutter.
Use the bushcutter on the right side of the operator as Use the bushcutter on the right side of the operator as Use the bushcutter on the right side of the operator as
Use the bushcutter on the right side of the operator as Use the bushcutter on the right side of the operator as
illustrated Fig. 13. illustrated Fig. 13. illustrated Fig. 13. illustrated Fig. 13. illustrated Fig. 13.
Always check the cutting tool for cracks after hitting foreign
objects.
ACTIVE NYLON HEAD SYSTEM "ACTIVE patent" Fig. 14
- Only use line of the same diameter as the original to avoid
overloading the engine.
- Stop the engine and put on the safety gloves.
Turn the knob (C), clockwise, until the arrow (E) is in line
with one of the eyelets (D). Insert the pipe (A) Through both
eyelets fit the line through the pipe.
- Remove the pipe on either side of the nylon head.
FUEL
2 STROKE - WARNING. The machine is equipped with a
two stroke engine. Always run the machine with fuel, which
is mixed with oil. Only prepare the quantity of fuel for each
job. Do not smoke. Refill when the engine is switched off and
away from naked flame. AIways use a minimum octane
number of 90. Mix fresh gasoline and ACTIVE oil in the ratio
of 50:1 (2%). If the ACTIVE oil is not available use a good 2
stroke oil quality in the ratio of 25:1 (4%) see fig.15
Important Always shake this fuel mix vigorously each time
you use it. Fuel mix properties deteriorate with time we
therefore recommend that you only make the quantity of fuel
mix you will need for each usage. Do not use fuel mix more
than a week old as this could damage the engine. Fill the
brushcutter fuel tank only to 3/4 capacity to allow for fuel
expansion.
6. ENGINE OIL (ONLY FOR 4 STROKE)
7. USE OF BRUSHCUTTER
8. PREPARING FOR USE
25
Fig. 12/2 Fig. 12/2
Fig. 12/2 - To unfasten the hook push at the same time the Fig. 12/2 Fig. 12/2
two levers (A) as show in the picture.
Is goodl monitored daily before use
strengthen the machine, the oil level.
The level should be between references and MIN MAX
sull'asta control.
For the replacement of exhausted (see Figure 9), simply
unscrew the cap and tilt the engine on the side of the hole
by the oil spill in a container placed under.
With the engine warm, act with great caution:
danger of burns.
The oil must be disposed exhausted in the appropriate
collection centers because it contains substances harmful
to the environment.
- Pull the line till the ends of the line are at the same length.
- turn the knob clockwise (every 3 turns stretch the lines)
until the line is wound onto the spool.
TO USE LINE FEEDER
Keep the engine at high RPM and tap or knock the underside
of the nylon head knob against the ground. Each knock will
feed approximately 3cm. of line.
WARNING: Do not knock the nylon head against hard
surfaces.
WARNING: fig.20 - only in extreme cases where one
has no alternative but to operate the brushcutter
on the left hands side of your body it is imperative to fit an
elbow (1) to the muffler (3). Before securing the elbow (2) it
is necessary to position it in such a way as to deflect the hot
gases away from the harness and the back of the operator.
4 STROKE - WARNING: the machine is equipped with a four
stroke engine which is working only with petrol. Do not
smoke. Refill when the engine is switched off and away from
naked flame. AIways use petrol with a minimum octane number
of 90.
Fill the brushcutter fuel tank only to 3/4 capacity to allow for
fuel expansion.
FUELING
WARNING Always shut off the engine before refueling. Slowly
open the cap of the fuel tank, when filling up with fuel, so that
possible over pressure disappears. Tighten the fuel cap
carefully after fuelling. Always move the machine at least 3
m (10Ft) from the fueling area before starting. Before fueling
clean the tank cap area carefully, to ensure that no dirt falls
into the tank make sure that the fuel is well mixed by shaking
the container before fueling.
ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH GB