Active 3.5-Z 4T Manual De Instrucciones página 24

Ocultar thumbs

página de 64

/ 64

Idiomas disponibles

ENGLISH

ENGINE / TRANSMISSION ASSEMBLY

Fig. 2

Fig. 2 - Introduce the end of the flexible transmission (A) into

Fig. 2

the clutch housing (B). Make sure the square of the inner

flexible shaft(G) is fitted correctly into the square hub of the

clutch drum. Secure it by the screw (C).

Make sure the screw (C) locate the hole (D). Connect the

clutch housing(B) to the engine (E) by means the screws

(F).

FITTING THE THROTTLE CABLE AND STOP SWITCH

WIRES

Fig.3

Fig.3 - Remove the filter cover (16) fig.1

Fig.3

- Introduce the throttle cable (A) through of the cable tensioner

(B). Make sure that the cable sheath (C) rest against the

inside of the tensioner (B). Ensure that the throttle lever is

not in half-throttle, then connect the cable terminal in the

clamp (E). Adjust cable tension (A) by loosening the lock

nut (D) and turning the tensioner (B). Once the correct tension

is reached, tighten the lock nut (D). lf adjusted correctly,

throttle trigger will move freely approximately 2 mm before

carburettor lever (E) moves. Connect the stop switch wires

(F- G).

FITTING THE LOOP HANDLE

Fig 4

Fig 4- remove the screws (I) open the loop handle (Q) in

Fig 4

order to slip it on to the tube (C) and secure it by means the

screws (I) and the nuts (M). Fit the safety bar (N) into it's

seat and secure it by means the screws (O) and nut (P).

The position of the handle could be adjusted according with

the requirements of the operator.

ASSEMBLY GEAR HEAD AND SAFETY GUARD

Fig.5 -

Fig.5 - Remove the screw (1) and loosen the screws (2)

Fig.5 -

- Slip the plastic bush (3), gear head side, on the transmission

tube (4) to locate at 40mm. from the end of the tube (4).

- Fit the gear head (5) on the transmission tube (4).

- Secure the braket (6) on the gear head (5) by the screws

(1). Make sure that the screw face the hole on the transmission

tube (7) and secure the gear head with the screws (2).

Fig.6 -

Fig.6 - Fit the guard (8) on the transmission tube (4) and

secure it by the bracket (6), screws (2), plates (3) and nuts

(7).

DANGER: make sure the bracket (6) is secured on

to the gear head (5) by the screw and washer (1).

Do not tamper or change the position of the cutting

tool safety guard. For safety reason's use the saw blades

only with the specific safety guard and not with the

standard one.

BLADE ASSEMBLY

Fig. 7

Fig. 7 - Loosen the nut (D) clockwise; remove cup (E) (only

if is the skid unit version) and lower flange (C).

- Fit the blade as showed in the picture making sure that the

upper flange (A) is well fitted.

- Fit the blade making sure that the rotation direction is correct

(the inscription on the blade should be facing up).

- Fit the lower flange (C), the cup (E) (only if is the skid unit

version) tighten the nut (D) anti-clockwise at 30 Nm ( 3.0

kgm).

5. ASSEMBLY

- While tightening the nuts (D), the blade can be held fast by

inserting the allen key Ø 4 mm into the cap, the upper flange

and gear case holes (F). To do this, rotate the cutiing tool

until the two holes coincide.

NYLON HEAD ASSEMBLY

Fig. 7 -

Fig. 7 - Loosen the nut (D) clockwise; remove cup (E) (only

if is the skid unit version) and lower flange (C) see fig.7.

Fig. 8 -

Fig. 8 - Assemble the nylon head (1) as illustrated.

Fig. 8 -

Fig. 9 -

Fig. 9 - Fit the upper flange (A) and the nylon head (1)

Fig. 9 -

tighten only by hand COUNTERCLOCKWISE .

The nylon head is held fast in the manner described in Fig.7

WARNING:

WARNING: for your safety use only genuine cutting tools.

WARNING:

FITTING THE ATTACHMENTS (A-B-C) ON THE MACHINE

Fig.10

Fig.10 - Loose, counter-clockwise, the lever (1).

Fig.10

- Slip the tube (2) into the coupling (4) as far as the reference

(3) (about 40mm.). In order to ease the introduction of the

inner shaft (5) into the coupling shaft (6), twisting slightly

one way and the other the attachment till it is slipped to the

ref. (3).

To rotate the attachment in the working position and secure

it by the lever (1).

FITTING THE EXTENSION (option only for A - B - C

attachments)

Fitting extension / machine fig.11

- Loosen, counter-clockwise, the lever (1).

- To slip the extension tube (2) into the coupling (4) as far as

the reference (3) (about 40mm.). Rotate the extension in order

to locate the coupling (10) in the same position as the coupling

(4) and secure it by the lever (1).

Fitting attachment / extension fig.11

- loosen, counter-clockwise, the lever (7).

- To slip the attachment tube (8) into the coupling (10) as far

as the reference (9) (about 40mm.) In order to introduce the

shaft (11) with ease into the extension coupling shaft, twist

slightly one way and the other the attachment, till the tube is

fully introduced.Rotate the attachment in the working position

and secure it by the lever (7).

WARNING: to use the attachments A-B and C see

WARNING:

the specific owner's manual.

The maximum extension allowed is 1.500mm.,

otherwise it is dangerous. Only one extension each time

can be used on the machine, the 750mm. or alternatively

the 1.500mm..

HARNES

The ACTIVE harness is ergonimic, ensure the maximum

comfort and allows one to operate safely.

In order to operate in the best conditions and to profit by the

exeptional features of this harness need to be adjusted

correctly.

Fig.12

Fig.12- Put on the harness and clip the buckles (A-B)

- Adjust the tension of the strap pulling or loosening the straps

(D).

- Adjust the tension of the shoulder straps (E) pulling or loosening

the straps (F).

- Adjust the pressure of the back harness by pulling or loosening

the straps (C).

to use the attachments A-B and C see

Productos relacionados para Active 3.5-Z 4T

Este manual también es adecuado para:

4.0-z 2t 5.5-z 2t 4.5-z 2t 6.5-z 2t

Active 3.5-Z 4T Manual De Instrucciones página 24

Idiomas disponibles

Manuales relacionados para Active 3.5-Z 4T

Productos relacionados para Active 3.5-Z 4T

Este manual también es adecuado para: