Scheppach HM216SPX Traduccion Del Manual De Instrucciones Originale página 34

6. Technical data
AC motor ......................................... 220 - 240 V~ 50 Hz
Power S1 ........................................................1700 Watt
Operating mode ...................................S6 25%* 2000W
Idle speed n0 ............................................... 4800 min-1
Carbide saw blade ..................... ø 210 x ø 30 x 2,6 mm
Number of teeth ......................................................... 24
Maximum tooth width of saw blade ...................... 3 mm
Swivel range .......................................... -45° / 0°/ +45°
Mitre cut ........................................... 0° to 45° to the left
Saw width at 90° ....................................... 340 x 65 mm
Saw width at 45° ....................................... 240 x 65 mm
Saw width at 2 x 45°
(double mitre cut)) ..................................... 240 x 38 mm
Protection class .................................................... II /
Weight ......................................................... ca. 12,15 kg
Laser class ................................................................... 2
Wavelength of laser ........................................... 650 nm
Laser output ....................................................... < 1 mW
* S6, continuous operation periodic duty. Identical duty
cycles with a period at load followed by a period at no
load. Running time 10 minutes; duty cycle is 25% of the
running time.
The work piece must have a minimum height of 3
mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise
Total noise values determined in accordance with
EN 62841.
Sound pressure level L
pA
Uncertainty K ....................................................... 3 dB
pA
Sound power level L .....................................109,5 dB
WA
Uncertainty K ....................................................... 3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
The above-mentioned noise emission values were
measured in accordance with a standardised test pro-
cedure and can be used to compare one power tool
with another.
The above-mentioned noise emission values can also
be used for the preliminary assessment of exposure.
34 | GB
...................................96,5 dB
www.scheppach.com
Warning:
• The noise emissions during the actual use of the
power tool may differ from the above-mentioned
values depending on the power tool being used, in
particular on the type of workpiece being processed.
• Try to keep emissions as low as possible, for ex-
ample by limiting your working time. In this regard,
all the operational cycle phases must be taken into
consideration (such as the times when the tool is
switched off or running idle).
7. Before starting the equipment
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be set up where it can stand
securely. Secure the machine on a workbench, base
frame or similar. Insert 4 screws (not included in the
scope of delivery) into the holes on the fixed saw
table (15). Tighten up the screws.
• Loosen the tilt protection (36) pre-installed at the
bottom of the saw, completely pull it out and secure
it with an Allen key (D).
• Adjust the adjusting screw (38) to the level of the tab-
letop to avoid wobbling of the machine.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power sup-
ply make sure the data on the rating plate are identi-
cal to the mains data.