Technical Data - Scheppach HM254SPX Traduccion Del Manual De Instrucciones Originales

19. Only use the supplied saw blade for cutting wood,
never for the processing of metals.
20. Only use saw blade diameters in accordance with
the markings on the saw.
21. Use additional workpiece supports, if required for
workpiece stability.
22. Workpiece support extensions must always be se-
cured and used during work.
23. Replace table inserts when worn!
24. Avoid overheating of the saw teeth.
25. When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose.
Replace damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine.
Allow the saw blade to cool down before using the
machine again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still remain.
32 | GB
• Residual risks can be minimised if the „Safety infor-
mation" and the „Proper use" are observed along
with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your machine provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch off the ma-
chine prior to any operations.
Warning!
This electric tool generates an electromagnetic field
during operation. This field can impair active or passive
medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recom-
mend that persons with medical implants consult with
their physician and the manufacturer of the medical im-
plant prior to operating the electric tool.

6. Technical data

AC motor ........................................ 220 - 240 V~ 50 Hz
Power S1 ....................................................... 1800 Watt
Operating mode ................................. S6 25%* 2200 W
Idle speed n
Carbide saw blade .....................ø 254 x ø 30 x 2,8 mm
Number of teeth .........................................................48
Maximum tooth width of saw blade ...................... 3 mm
Swivel range ..........................................-45° / 0°/ +45°
Mitre cut ...........................................0° to 45° to the left
Saw width at 90° .......................................340 x 90 mm
Saw width at 45° .......................................240 x 90 mm
Saw width at 2 x 45°
(double mitre cut)) ..................................... 240 x 46 mm
Protection class ....................................................II /
Weight .......................................................... ca. 14,4 kg
Laser class ................................................................... 2
Wavelength of laser ...........................................650 nm
Laser output .......................................................< 1 mW
www.scheppach.com
.................................................4800 min
0
-1