Idiomas disponibles
Idiomas disponibles
The Dolby Pro Logic feature
and the center and rear speakers
(standard)
assure
full-scale
home theater sound.
When playing
back laser
discs
or video
software
that have
been
specially
recorded
with four-channel
sound (left, right, center,
rear) and
steering
logic (for sound
directionality),
astonishingly
realistic
sound surrounds
the listener to create a new level of audio/visual
entertainment.
Independent
control of the four sound channels allows the listener
to enjoy the same
type of sound
reproduction
experienced
in
movie theaters.
Voices
are reproduced
in the front and center
sound
field, while
ambient
sounds
like cars and crowds
are
reproduced
on all sides of the listener
for an incredibly
lifelike
audio/video
experience.
Please
read the following
carefully
to
"tune" the system's
output
to match the characteristics
of your
listening
space,
Check the following:
• Before using the DOLBY PRO LOGIC, adjust the proper
balance of speaker sound levels.
• Make sure the supplied speakers are properly connected and
positioned. (See page 3)
• Make sure the TV set and video unit are properly connected.
(See page 4)
• Make
sure
the laser
disc,
video
tape,
etc.,
support
1313[ ...... u.._.N_].
ADJUSTING SPEAKER LEVEL B ALANCE
2,4
i
i
BALANCE
The unit is equipped
with a built-in
test signal generator
called a
noise sequencer
for easy balance adjustment
of all four channels.
The sequencer
outputs a noise signal that "travels"
from channel
to channel,
enabling
the simple
adjustment
of sound
level to
achieve,
at the listening
position,
the same apparent
loudness
from each channel.
Use the remote control.
1 Press
the
DOLBY
PRO LOGIC
button
to select
NORMAL.
If PHANTOM or 3CH LOGIC appears, press the DOLBY PRO
LOGIC button repeatedly until NORMAl_ is selected_
2 Press
the MANUAL
SELECT
(TEST)
button
and
hold
it down
for about
four seconds
until "L-CH"
lights.
3 Adjust
the
sound
level
of the center
and
the
surround
speakers.
While "C" or "S" is displayed, press the DOWN 14,4 or UP
IH_I button to adjust the volume of the center or surround
speakers to match the level of the left and right speakers.
To adjust the balance between the left and right speakers,
use the BALANCE control while "L" or "R" is displayed.
4 Press the MANUAL
SELECT
(TEST)
button
again
to stop the noise signal.
If the surround
speakers
volume
of the DSP is changed
(See
page 7), {he DOLBY
PRO LOGIC
level is also changed.
About the channels
The left and right speakers create the stereo effect.
The center speaker helps achieve precise sound positioning
over a broad sound field.
The rear-mounted surround speakers enhance the "depth" of
the sound field.
To change
the delay
time
The surround
speakers
reproduce
sounds
a split second
after
the
front
speakers.
The
delay
is initially
set
to 20
ms
(milliseconds).
To change this standard
delay time, press the MANUAL SELECT
(TEST)
button
on the remote control
three times
in NORMAL
mode
(or twice
in PHANTOM
mode)
so that "T" is displayed.
Then, press the DOWN I_14 or UP I_IH button. Each time one of
the buttons is pressed, the delay time changes
as shown below.
20ms _
30rns
To change
the sound
levels
after
adjusting
the balance
with the noise
sequencer
The sound
levels
of the center
or surround
speakers
can be
adjusted
during
playback
of laser discs or video software.
1
Press the MANUAL
SELECT
(TEST)
button
on the remote
control
once or twice to select "C" (center)
or "S" (surround).
2 While the "C" or"S" is displayed,
press the DOWN 14"q or UP
IH_I button on the remote control to adjust the volume.
A noise signal is sent to each channel
in turn in the following
sequence.
_
L-CH: Left speaker
---_
R-CH: Right speaker
3
S: Surround
speakers
*---C:
Center speaker ._J
17 ENG,IS.
