Hama Nano Instrucciones De Uso página 7

7.1 Before you start the learning function
• Make sure that all batteries used in both remote controls are in perfect condition.
Change them if necessary.
• Place your original remote control and the universal remote control next to each other
so that the infrared diodes of the remote controls are directly opposite each other.
• If necessary, correct the height of both remote controls to achieve optimal alignment.
• The distance between the two remote controls should be approx. 3 cm.
Nano
Note
• Do not move the remote controls during the learning process.
• Make sure that the room lighting is not uorescent tubes or energy-saving lamps,
as these could cause interference and thus hinder the learning process.
• The distance between the two remote controls and the nearest light source should
be at least 1 metre.
• In learning mode, each button can only be assigned one function. A new function
overwrites the function previously taught on this button.
• Press the Setup button to end the learning function.
• Except for the Setup button, all button can be assigned a taught-in function.
7.2 Activating the learning function / transferring the button function
1. Press and hold the Setup button for approx. 3 seconds until the LED lights up to
start Setup mode.
2. To teach a command in TV mode, enter the code 9 8 0 0 0 or 9 8 0 0 1 for STB
mode.
3. Press the key of the NANO FB to which you want to teach a new function. The LED
ashes 2x and then lights up permanently. If no button is pressed within 15 seconds,
the LED ashes 6 times and the learning function is terminated.
4. Now press the button on the original remote control whose function you want to
transfer.
If the LED goes out brie y and then lights up again permanently, the function has
been successfully taught. If the LED ashes 6 times quickly, the transfer has failed.
Check the position of the two remote controls and make sure the batteries are full.If
no command is received within 35 seconds, the LED ashes 6 times and the learning
function is terminated.
5. To teach more buttons, repeat steps 3 and 4.
6. After you have transferred all the desired functions, press the SETUP button to save
all the taught-in functions and exit Learning mode.
ORIGINAL
ca. 3 cm
Note
When changing the batteries of the universal remote control, the functions of the
taught-in buttons are retained.
7.3 Deleting taught functions
7.3.1 Deleting a taught function
1. Press and hold the Setup button for approx. 3 seconds until the LED lights up
permanently to start Setup mode.
2. Enter the code 98100 for TV mode or 98101 for STB mode. The LED ashes once.
3. Press the button of the NANO FB whose taught-in function is to be deleted.
4. The LED ashes once, the taught-in function is deleted and has been replaced by the
function of the factory setting.
5. To delete more buttons, repeat step 3.
6. To exit the menu, press the Setup button.
7.3.2 Deleting all taught functions
1. Press and hold the Setup button for approx. 3 seconds until the LED lights up
permanently to start Setup mode.
2. Enter the code 98200 to delete all taught-in buttons in TV mode or 98201 to delete
all taught-in buttons in STB mode.
3. The LED ashes 2 x, all taught-in functions are deleted and are replaced by the
functions of the factory setting.
8. Restoring factory settings
1. Press and hold the Setup button for approx. 3 seconds until the LED lights up
permanently to start Setup mode.
2. Enter the number 99999.
3. All settings and taught-in functions are deleted and are replaced by the functions of
the factory setting.
9. Switching illumination on/off
• Press the Power and Mute buttons simultaneously.
• If the LED ashes green once, the illumination of the remote control is switched on.
• If the LED ashes red once, the illumination is switched off.
• When the illumination is switched on, it goes out each time the button is pressed and
lights up again for approx. 3 seconds as soon as the button is released.
10. Maintenance
• Never use old and new batteries in the universal remote control at the same time, as
old batteries tend to leak and can lead to a loss of performance.
• Never clean the universal remote control with scouring agents or harsh cleaning
agents.
• Keep the universal remote control free of dust by cleaning it with a dry soft cloth.
5