Idiomas disponibles
Idiomas disponibles
2. Introduction
MANUFACTURER:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
In accordance with the applicable product liability laws, the
manufacturer of this device assumes no liability for damage to
the device or caused by the device arising from:
• Improper handling
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Improper use
• Failures of the electrical system in the event of the electri-
cal regulations and VDE provisions 0100, DIN 57113 /
VDE0113 not being observed.
Note:
Read the whole text of the operating manual before assembly
and commissioning.
This operating manual should help you to familiarise yourself
with your product and to use it for its intended purpose.
The operating manual includes important instructions for the
safe, proper and economic operation of the product, for avoid-
ing danger, for minimising repair costs and downtimes and for
increasing the reliability and extending the service life of the
product.
In addition to the safety instructions in this operating manual,
you must also observe the regulations applicable to the opera-
tion of the product in your country.
Keep the operating manual package with the power tool at
all times and store it in a plastic cover to protect it from dirt
and moisture. They must be read and carefully observed by all
operating personnel before starting the work.
The product may only be used by personnel who have been
trained to use it and who have been instructed with respect to
the associated hazards.
The required minimum age must be observed.
In addition to the safety instructions in this operating manual
and the separate regulations of your country, the generally
recognised technical rules relating to the operation of such ma-
chines must also be observed.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.
3. Device description (fig. 1-2)
1.
Pressure connection (1 inch internal thread)
1a Locking screw
2.
Transport handle
3.
LCD display
4.
MODE button
5.
SET button
6.
CHECK button
7.
Fastening points (diameter of 6 mm)
8.
Ventilation screw
9.
Water drain plug
10. Suction connection (1 inch internal thread)
10a Locking screw
11. Pre-filter locking screw
12. Pre-filter
13. Multifunction adapter
13a Double nipple
13b Angle piece
4. Scope of delivery
• Garden pump and domestic waterworks
• 2x multifunction adapters (two pieces)
• Operating manual
5. Proper use
The machine may only be used in the intended manner. Any
use beyond this is improper. The user/operator, not the manu-
facturer, is responsible for damages or injuries of any type re-
sulting from this.
An element of the intended use is also the observance of the
safety instructions, as well as the assembly instructions and op-
erating information in the operating manual. Persons who oper-
ate and maintain the machine must be familiar with it and must
be informed about potential dangers.
In addition, the applicable accident prevention regulations
must be strictly observed. Other general occupational health
and safety-related rules and regulations must be observed. The
liability of the manufacturer and resulting damages are exclud-
ed in the event of modifications of the machine.
Area of application
• For watering and irrigation of green areas, vegetable beds
and gardens.
• For operating lawn sprinklers.
• With pre-filter for drawing water from ponds, streams, rain-
water barrels, rainwater cisterns and wells.
Pumped media
For pumping clear water (fresh water), rainwater or light deter-
gent solutions / domestic water.
• The maximum temperature of the pumped liquid must not
exceed +35°C.
• This garden pump and domestic waterworks must not be
used to pump flammable, gaseous or explosive liquids.
• The pumping of aggressive liquids (acids, lyes, silo seepage
juice etc.), as well as liquids with abrasive (sanding) materi-
als (sand) must also be avoided.
GB/IE
3
