Scheppach HMS850 Traduccion Del Manual De Instrucciones Originale página 39

• (wide, flat workpieces see fig. 10) Open the star
grip nut (6) and set the planing blade cover cpl (13)
just as high as the workpiece is thick. The planer
blade cover (7) covers the entire knife! Tighten the
star grip nut (6) again.
• Plug in the machines power cord. Press the green
button "I" to start the planing machine.
• Place the workpiece you wish to plane on the feed
table (12). Slide the workpiece as far as possible
with the push stick (16) forwards towards the plan-
ing table (26) over the knives (24).
• When you have finished work, switch off the ma-
chine. To do this, press the red button "0". Then dis-
connect the machine from the mains supply.
• Remove the chips and dust from the feed table (12),
planing table (26) and knife block after the machine
has reached a complete standstill.
• Bring back the planer blade cover (7) and cover the
planer blade over its entire length.
10.2 Thicknessing
m IMPORTANT!: Pull out the power plug before
performing any maintenance, cleaning and adjusting
work.
10.2.1 Adjustment (fig. 4/11)
Place the crank handle (10) on the spindle (19) and
turn it to adjust the thicknessing table (21) to the re-
quired height. The set angle can be read off the scale
(C).
10.2.2 Thicknessing mode (fig. 4/11/12)
Attention! Watch out the right mounting of the chip ex-
tractor (point 8.4)
• Plug in the machines power cord. Press the green
button "I" to start the plane.
• Place a workpiece on the thicknessing table (21).
Guide the workpiece towards the feed table (12).
• When you have finished work, switch off the ma-
chine. To do this, press the red button "0". Then dis-
connect the machine from the mains supply.
• Remove the chips and dust from the thicknessing
table (21) and knife block after the machine has
reached a complete standstill.
10.3 Changing the knives (fig. 13/14)
• m IMPORTANT!: Always pull the mains plug be-
fore changing the knives.
• Pull the planing knife cover (13) forwards as far as
possible so that the entire knife block is exposed.
• Release and remove the four knife clamping screws
(23).
• Lift the knives (24) and knife block (27 from the cut-
ter block.
• Remove the chips and any resin from the cutter
block and knife support.
• Place new knives (24) into the cutter block and fix
them with the rectangle slots in both screw heads.
(With these two screws, height-adjustment of the
knife is done.)
• Place the knife block (27) onto the knife (24).
• Slightly tighten the four clamping bolts (23).
• Repeat these actions for the second knife (24).
• Then adjust the planer/thicknesser knives (24) ex-
actly with the output table. Use a ruler that you put
onto the output table.
• By the two set screws (31), the knife (24) can be
adjusted for height.
• By turning the cutter block and using the ruler, you
can see the height adjustment.
• The knife is exactly set, when the ruler is moved by
the knives not higher than 3 mm.
• After a successful knife setting, all clamping screws
must be tightened (8.4 N/m).
Please mind:
• Sharp planer/thicknesser knives guarantee a clean
planing surface and put less stress on the motor.
• After three grinding actions, a maximum material
removal of 3 x 0.05 mm may not be exceeded.
• The planer/thicknesser blades used on this machine
are not suitable for rebating and dovetailing.
• Finally lower the cutter block guard again onto the
table. Cover the cutter block and block it with the
star grip screw.
m IMPORTANT!
Only use knives which are recommended by the man-
ufacturer for this equipment. If you use other knives
there is a risk of injuries due to lack of control.
Avoid over-tightening and the possibility of the thread
becoming detached. If the latch or the screws have
worn out threads they must be immediately replaced.
www.scheppach.com GB | 39