Idiomas disponibles
Idiomas disponibles
ENgLish
2. After adding a gasoline stabilizer, run the engine
outdoors for 10 minutes to be sure that treated gasoline
has replaced the untreated gasoline in the carburetor.
3. Turn the fuel valve to the OFF position.
4. Continue to run the engine until it stops from the lack of
fuel in the carburetor fuel bowl. Running time should be
less than 3 minutes.
Pump
The manufacturer recommends using D
or equivalent when storing the unit for more than 30 days
and/or when freezing temperatures are expected. D
Pump Guard is environmentally friendly.
NOTE: Using pump guard helps provide proper lubrication
to the internal seals of the pump regardless of temperature
or environment.
NOTICE: Risk of property damage. Use only D
Pump Guard or equivalent. Other products could be
corrosive and/or contain alcohol which may cause
pump damage.
1. Turn off pressure washer and disconnect hoses
from pump.
2. Unscrew bottle valve from Pump Guard bottle and
remove seal.
3. Screw bottle valve back onto bottle.
4. Attach bottle to water inlet of pump.
5. Squeeze bottle to inject contents into pump.
6. With ignition switch off, simultaneously pull starter rope
and squeeze bottle. Repeat until protector fluid exits
pump outlet. NOTE: This step may require two people.
Pressure Washer
1. Drain all water from high pressure hose and wrap it onto
hose wrap.
2. Drain all water from the spray gun and wand by holding
spray gun in a vertical position with nozzle end pointing
down and squeezing trigger. Store in gun holder.
3. Wrap up and secure detergent siphon hose so it is
protected from damage.
Accessories
DANGER: Risk of fluid injection. When using
replacement spray wands or guns with this pressure
washer, DO NOT use a spray wand and/or spray gun/
wand combination that is shorter in length than what
was provided with this pressure washer as measured
from the nozzle end of the wand to the gun trigger.
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact D
WALT, call 1-877-362-4271.
e
14
WALT Pump Guard
e
WALT
e
WALT
e
WALT recommended
e
Repairs
WARNING:To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
To find the nearest service center, please contact D
1-877-362-4271.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• CONFiRMATiON OF OWNERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com
WALT factory service center or a
e
WALT, call
e
