Idiomas disponibles
Idiomas disponibles
ENgLish
•
Your washer operates at fluid pressures and
velocities high enough to penetrate human and
animal flesh, which could result in amputation or
other serious injury. Leaks caused by loose fittings
or worn or damaged hoses can result in injection
injuries. DO NOT TREAT FLUID INJECTION AS A
SIMPLE CUT! See a physician immediately!
DANGER: Carbon Monoxide. Using an engine
indoors can kill you in minutes. Engine exhaust
contains high levels of carbon monoxide (CO),
a poisonous gas you cannot see or smell. You
may be breathing CO even if you do not smell
engine exhaust.
•
Breathing ex haust fumes will cause se ri ous injury or
death! En gine exhaust contains carbon mon ox ide,
an odorless and deadly gas.
•
Operate pressure washer in a well-ventilated
area. Avoid en closed areas such as ga rages,
basements, etc.
•
Never op er ate unit in or near a lo ca tion occupied
by humans or animals.
WARNING: Risk of Fire, Asphyxiation and Burn.
Never fill fuel tank when engine is running or hot.
Do not smoke when filling fuel tank.
•
Never fill fuel tank completely. Fill tank to 1/2"
(12.7 mm) below bottom of filler neck to provide
space for fuel expansion. Wipe any fuel spillage
from engine and equipment before starting engine.
•
DO NOT let hoses come in contact with very hot
engine muffler during or immediately after use
of your pressure washer. Damage to hoses from
contact with hot engine surfaces will NOT be
covered by warranty.
NOTICE: Risk of property damage. Never pull water
supply hose to move pres sure washer. This could
damage hose and/or pump inlet.
•
DO NOT use hot water, use cold water only.
•
Never turn water supply off while pressure washer
engine is running or damage to pump will result.
•
DO NOT stop spraying water for more than two
minutes at a time. Pump operates in bypass
mode when spray gun trigger is not pressed. If
pump is left in bypass mode for more than two
minutes internal components of the pump can
be damaged.
If you do not understand these precautions, visit our website at
www.dewalt.com for a list of service centers, or call D
at 1-877-362-4271.
Prior to starting, refer to your engine manual for proper
starting procedure.
1. In a well ventilated outdoor area add fresh, high quality,
unleaded gasoline with a pump octane rating of 86
or higher. Do not overfill. Wipe up spilled fuel before
starting the engine. Refer to Engine Owner's Manual
for correct procedure.
12
IMPORTANT: Ethanol Shield™ (sold separately) is a fuel
stabilizer that helps eliminate and prevent ethanol
related problems in power equipment. Follow the
instructions on the container and add to the gasoline.
NOTICE: Use of fuels with greater than 10% ethanol
are not approved for use in this product per EPA
regulations and will damage the unit and void
the warranty.
2. Check engine oil level. See Engine Owner's Manual for
correct procedure.
3. Connect the water hose to the water source. Turn the
water source on to remove all air from the hose. When
a steady stream of water is present, turn the water
source off.
4. Verify the filter screen
NOTE: Convex side faces out.
5. Connect water source
NOTE: Water source must provide a minimum of 5
gallons per minute at 20 psi.
6. Connect high pressure hose
WARNING: To reduce the possibility of
contamination always protect against backflow
when connected to a potable water system.
7. Choose the correct nozzle for the job to be performed. See
how To Use spray Wand instructions in this section.
NOTE: If applying a chemical or cleaning solution,
see how To Apply Chemicals/Cleaning solvents
instructions in this section.
8. Turn water source on.
NOTICE: Risk of property damage. Failure to do so
could cause damage to the pump.
9. Remove all air from the pump and high pressure hose
by depressing trigger until a steady stream of water
is present.
10. Start engine. See Engine Owner's Manual for
correct procedure.
WARNING: Risk of unsafe operation. If engine
does not start after two pulls, squeeze trigger
of gun to relieve pump pressure. Pull starter
cord slowly until resistance is felt. Then pull cord
rapidly to avoid kickback and prevent hand or
arm injury.
11. Depress trigger on gun to start water flow.
WALT
e
WARNING: Risk of unsafe operation. Stand
on a stable surface and grip gun/spray wand
firmly with both hands. Expect the gun to kick
when triggered.
12. Release trigger to stop water flow.
13
is in water inlet of pump.
14
to pump inlet
10
.
3
to pump outlet
9
.
