Idiomas disponibles
Idiomas disponibles
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Lanyard Connection (Fig. A)
Optional Accessory
safety Warnings specific for Use At height
WARNING:
•
If the tool is dropped for any reason the lanyard
connection must be inspected and properly
serviced prior to re‑use. The lanyard connection is
designed to stretch to absorb the shock of a drop.
Any permanent stretch to the connection exposing
the red marked internal coils indicates it has been
compromised and must be serviced prior to reuse.
•
Do not use hang hook as lanyard
attachment point.
•
Only use batteries that contain the integral battery
strap. Do not use unsecured batteries while the tool
is tethered. Unsecured batteries may detach from
the tool if dropped.
•
Always keep the tool and accessories tethered
when working "at height". (Maximum lanyard
length: 6.5 ft [2 m].)
•
Use only with lanyards appropriate for this tool
type and rated for at least the weight identified on
the tool lanyard attachment point label.
•
Crush, cut or entanglement hazard. Do
not use near moving parts, mechanisms or
running machinery.
•
Do not anchor the tool lanyard to anything on
your body. Anchor to a rigid structure that can
withstand the forces of a dropped tool.
•
Make sure the lanyard is properly secure at each
end prior to use.
•
Inspect tool and lanyard before each use for
damage and proper function (including fabric
and stitching). Do not use if damaged or not
functioning properly.
•
Do not alter the lanyard attachment point or use in
a manner other than as instructed in this manual.
•
Only attach tool to a lanyard with a locking
carabiner. Do not attach by looping or knotting the
lanyard. Do not use rope or cord.
•
Electrical shock hazard. Be sure power is off when
working in high voltage areas. Some lanyards
are conductive.
•
Dropped tools will swing on the lanyard, which
could cause injury or loss of balance.
•
Do not carry the tool by the attachment point, the
battery strap or the lanyard.
•
Do not attach more than one tool to each lanyard.
•
Only use appropriate D
attachment kit. NEVER modify tools to create
attachment points.
•
Only transfer the tool between hands while
properly balanced in a stable orientation.
•
Do not attach lanyards to tool in a way that
keeps guards, switches or lock‑offs from
operating properly.
•
Avoid getting tangled in the lanyard.
•
Keep lanyard away from the cutting area of
the tool.
•
Do not use lanyards or attachment devices to get
additional leverage from the tool.
•
Do not use for personal fall protection.
•
Falling object hazard! Only change batteries,
accesories and attachments where a dropped
object won't cause a hazard below you. Consult
your Authority Having Jurisdication (AHJ) or site
supervisor for procedures for working at height.
•
Do not use the charger or contractor bag at height.
•
Use multi‑action or screw gate type carabiners. Do
not use single action spring clip carabiners.
16
The bracket
is for mounting the D
Attachment Point, available at a D
The lanyard-ready attachment kit is intended for use by
competent personnel who are trained and knowledgeable
regarding working with tools in and around machinery
and "at height". A lanyard-ready attachment kit may only
be added to certain models and must be installed by an
authorized service center.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
English
WALT brand lanyard‑ready
e
WALT Lanyard Ready
e
WALT service center.
e
9
