Idiomas disponibles
Idiomas disponibles
Push the anti-splinter guard (18) into the base plate (7)
from below (as shown in the figure with the groove facing up-
wards).
Cut Control (accessory)
Cut Control enables the power tool to be guided precisely
along a cutting line marked on the workpiece. Cut Control
includes the viewing window (11) with cut marks and the
base (9) for securing to the power tool.
Securing Cut Control to the base plate (see figure F)
Firmly insert the viewing window for Cut Control (11) into
the brackets on the base (9). Then push the base together
gently and allow it to click into place in the guide (19) on the
base plate (7).
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Hood (accessories) (see figures G and H)
Fit the hood (8) before you connect the power tool to the
dust extraction system.
Position the hood (8) on the power tool so that the two outer
brackets engage in the recesses of the housing.
Remove the hood (8) when working without a dust extrac-
tion system and for mitre cuts. To do this, push the hood to-
gether at the level of the outer brackets and remove it by
pulling it forwards.
Connecting the dust extraction system (see figure I)
Push the dust extraction adapter (20) (accessory) onto an
extraction hose (21) (accessory) until you hear it click into
place. Connect the dust extraction adapter (20) to the ex-
traction outlet (6) on the power tool and the extraction
hose (21) to a dust extractor (accessory).
You will find an overview of connecting to various dust ex-
tractors at the end of these operating instructions.
For optimum dust extraction, where possible use the anti-
splinter guard (18).
The dust extractor must be suitable for the material being
worked.
Bosch Power Tools
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation
Operating modes
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Adjusting the mitre/bevel angle (see figure J)
The base plate (7) can be swivelled to the right or left to
make mitre cuts up to 45°.
The hood (8) and anti-splinter guard (18) cannot be used
while mitre cuts are being made.
– Remove the hood (8), the anti-splinter guard (18) and
the glide shoe (17).
– Pull the saw blade storage compartment (16) out of the
base plate (7).
– Loosen the screw (23) and push the base plate (7)
slightly towards the extraction outlet (6).
– The base plate has lock-in points at 0°, 22.5° and 45° on
the left and right so that the precise mitre/bevel angle can
be adjusted. Swivel the base plate (7) to the required po-
sition according to the scale (22). Other mitre/bevel
angles can be adjusted using a protractor.
– Then push the base plate (7) towards the saw blade (10)
as far as it will go.
– Retighten the screw (23).
Cut Control for mitre cuts (see figure K)
To enable you to track the cutting line (Cut Control), the
viewing window for Cut Control (11) has a mark (24) for
right-angled cuts at 0° and a mark (25) for rightward- and
leftward-slanting mitre cuts at 45° according to the scale
(22).
The cut mark for mitre angles between 0° and 45° is propor-
tional. It can also be marked on the viewing window for
Cut Control (11) using a non-permanent marker and easily
removed again.
We recommend making a test cut for precise results.
Moving the base plate (see figure J)
You can move the base plate (7) back for sawing close to
edges.
Pull the saw blade storage compartment (16) out of the base
plate (7) or remove the glide shoe (17).
Loosen the screw (23) and push the base plate (7) towards
the extraction outlet (6) as far as it will go.
Retighten the screw (23).
Sawing with an offset base plate (7) is only possible with a
mitre angle of 0°. In addition, Cut Control must not be used
with the base (9), the parallel guide with circle cutter (27)
(accessory) or the anti-splinter guard (18).
English | 19
1 609 92A 846 | (04.08.2022)
