Idiomas disponibles
Idiomas disponibles
Installing or removing the chip receiver
Optional accessory
CAUTION:
When installing or removing the
chip receiver, always wear gloves so that your
hands do not directly contact the shear blades.
CAUTION:
Attach the blade cover before
installing or removing the chip receiver.
The chip receiver gathers discarded leaves and makes
clean-up afterward much easier. It can be installed on
either side of the tool.
1.
Align the holes on the chip receiver with the nuts
on the shear blades.
► Fig.16: 1. Nut
2.
Hook the claws of the chip receiver to the groove
on the shear blades.
► Fig.17: 1. Claw 2. Groove
3.
Press the levers on the chip receiver, and then
hook the claws on the other side to the groove on the
shear blades.
► Fig.18: 1. Lever
To remove the chip receiver, press the levers to release
the claws.
► Fig.19: 1. Lever
NOTICE:
Never try to remove the chip receiver
by an excessive force with its claws locked in the
grooves of the shear blades.
OPERATION
Operating the tool
WARNING:
Do not use the tool near any
electrical power lines. Contacting with power lines
or using the tool near power lines may cause serious
injury or electric shock resulting in death.
WARNING:
Keep hands away from shear blades.
WARNING:
Be extremely careful to maintain
control of the tool at all times. Do not allow the tool
to be deflected toward you or anyone in the work
vicinity. Failure to keep control of the tool could result
in serious injury to the bystander and the operator.
CAUTION:
Avoid operating the tool in very
hot weather as much as practicable. When operat-
ing the tool, be careful of your physical condition.
CAUTION:
Be careful not to accidentally con-
tact a metal fence or other hard objects while trim-
ming. The shear blades may break and cause an injury.
CAUTION:
Be careful not to allow the shear blades
to contact the ground. The tool may recoil and cause an injury.
CAUTION:
Overreaching with a hedge trimmer,
particularly from a ladder, is extremely dangerous.
Do not work while standing on anything wobbly or infirm.
NOTICE:
Do not attempt to cut branches thicker
than 10 mm in diameter with the tool. Cut branches
to 10 cm lower than the cutting height using branch
cutters before using the tool.
► Fig.20: (1) Cutting height (2) 10 cm
NOTICE:
Do not cut down dead trees or similar
hard objects. Doing so may damage the tool.
NOTICE:
Do not trim the grass or weeds while
using the shear blades. The shear blades may
become tangled in the grass or weeds.
Hold the tool with both hands by holding the front grip
and the rear grip.
► Fig.21: 1. Front grip 2. Rear grip
Pull the switch trigger while pressing the lock-off button,
and then move the tool forward.
► Fig.22
For basic operation, tilt the shear blades toward the
trimming direction and move it calmly and slowly at the
speed rate of 3 to 4 seconds per meter.
► Fig.23
To cut a hedge side evenly, cut from the bottom to top.
► Fig.24
When trimming to make a round shape (trimming box-
wood or rhododendron, etc.), trim from the root to the
top for a beautiful finish.
► Fig.25
If the chip receiver is attached to the shear blades, it
gathers discarded leaves and makes clean-up after-
ward much easier.
► Fig.26
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
CAUTION:
When inspecting or maintaining
the tool, always put the tool down. Assembling or
adjusting the tool in an upright position may result in
serious injury.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the tool
Clean the tool by wiping off dust with a dry cloth or one
dipped in soapy water and wrung out.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
13 ENGLISH
