Idiomas disponibles
Idiomas disponibles
Read all of manual to become familiar with this vehicle. Pay attention to all NOTICES, CAUTIONS, WARNINGS and DANGERS.
HARDWARE
Periodically, the vehicle should be inspected for loose
fasteners. Fasteners should be tightened in accordance
with the Torque Specifications table (Ref. Fig. 22).
Use care when tightening fasteners and refer to the
Technician's Repair and Service Manual for specific
torque values.
installed are considered 'wet' and require approximately 80% of the torque required for 'dry' fasteners.
BOLT SIZE
1/4"
4
Grade 2
(5)
6
Grade 5
(8)
6
Grade 8
(8)
BOLT SIZE
M4
1
Class 5.8
(2)
(Grade 2)
5.8
2
Class 8.8
8.8
(3)
(Grade 5)
3
Class 10.9
10.9
(4)
(Grade 8)
Fig. 22 Torque Specifications and Bolt Grades
To reduce the possibility of severe injury or
death from improper servicing techniques:
DO NOT attempt any type of servicing
operations before reading and understand-
ing all notes, cautions and warnings in this
manual.
Any servicing requiring adjustments to be
made to the powertrain while the motor is
running must be made with both drive
wheels raised and vehicle properly support-
ed on jack stands.
To reduce the possibility of motor damage,
never operate vehicle at full throttle for
more than 4 - 5 seconds while vehicle is in
a 'no load' condition.
OPERATION AND SERVICE INFORMATION
ALL TORQUE FIGURES ARE IN FT. LBS. (Nm)
Unless otherwise noted in text, tighten all hardware in accordance with this chart.
This chart specifies 'lubricated' torque figures. Fasteners that are plated or lubricated when
5/16"
3/8"
7/16"
8
15
24
(11)
(20)
(33)
13
23
35
(18)
(31)
(47)
18
35
55
(24)
(47)
(75)
M5
M6
M8
2
4
10
(3)
(6)
(14)
4
7
18
(6)
(10)
(24)
6
10
25
(8)
(14)
(34)
Owner's Guide
Generally, three grades of hardware are used in the ve-
hicle. Grade 5 hardware can be identified by the three
marks on the hexagonal head and grade 8 hardware is
identified by 6 marks on the head. Unmarked hardware
is Grade 2 (Ref. Fig. 22).
1/2"
9/16"
5/8"
35
55
75
(47)
(75)
(102)
55
80
110
(75)
(108)
(149)
80
110
170
(108)
(149)
(230)
M10
M12
M14
20
35
55
(27)
(47)
(76.4)
35
61
97
(47)
(83)
(131)
49
86
136
(66)
(117)
(184)
To reduce the possibility of causing an
electrical arc, which could result in a battery
explosion, turn off all electrical loads from
the battery before removing battery wires.
explosion.
Reduce the possibility of accidental starting
by removing and grounding spark plug
wires and disconnecting battery at negative
terminal before servicing.
The electrolyte in a battery is an acid solu-
tion which can cause severe burns to the
3/4"
7/8"
1"
130
125
190
(176)
(169)
(258)
200
320
480
(271)
(434)
(651)
280
460
680
(380)
(624)
(922)
Wear eye protection when
working on the vehicle.
Use extra care when
working around batteries,
or using solvents or com-
pressed air.
Wrap wrenches with vinyl
tape to reduce the possibil-
ity of a dropped wrench
'shorting out' a battery,
which could result in an
B
B
Page 15
